Festool OF 1400 EB Notice D'utilisation D'origine page 17

- Secure the copying ring (8.1) to the router base
by inserting both tenons (8.2) into the recesses
(8.3).
- To loosen the copying ring, press both buttons
(1.16) inwards simultaneously.
b) Copying device
The angle arm WA-OF (10.2) and copier scanning
set KT-OF, consisting of roller holder (10.6) and
three copying rollers (10.7), are required for the
copying device.
- Screw the angle arm at the desired height in the
platen's threaded bore (10.1) with the rotating
knob (10.3).
- Fit a copying roller in the roller holder and bolt
this to the angle arm with the rotating knob
(10.5). Make sure that the copying roller and
cutter have the same diameter!
- Turn the adjusting wheel (10.4) to adjust the dis-
tance between the copying roller and cutter axis.
7 Accessories
For your own safety, use only original
Festool accessories and spare parts.
Festool offers extensive accessories that enable
you to use your machine effectively for a wide
variety of applications, e.g.: routing circle, guide
rails with rows of holes, routing aid, router base
for bench-mounted use.
The accessory and tool order number can be found
in the Festool catalogue or on the Internet under
„www.festool.com".
8 Maintenance and care
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
All maintenance and repair work which
requires the motor casing to be opened
may only be carried out by an authorised
service centre.
The cool air openings in the motor casing must
always be kept clean and unobstructed to ensure
air circulation.
The tool is fi tted with special motor brushes with
an automatic cut-out. When the brushes become
worn the power supply is shut off automatically
and the tool comes to a standstill.
To alter the position of the clamping lever (see
Fig. 11):
- Release the screw.
- Remove the clamping lever and tighten the
hexagon screw.
- Insert the clamping lever again in the desired
position and lock it with the screw.
9 Disposal
Do not throw the power tool in your household
waste! Dispose of machines, accessories and
packaging at an environmentally-responsible
recycling centre. Observe the valid national regu-
lations.
EU only: European Directive 2002/96/EC stipulate
that used electric power tools must be collected
separately and disposed of at an environmentally
responsible recycling centre.
10 Warranty
Our equipment is under warranty for at least 12
months with regard to material or production
faults in accordance with national legislation.
In the EU countries, the warranty period is 24
months (an invoice or delivery note is required
as proof of purchase). Damage resulting from,
in particular, normal wear and tear, overloading,
improper handling, or caused by the user or other
damage caused by not following the operating
instructions, or any fault acknowledged at the
time of purchase, is not covered by the warranty.
Damage caused by the use of non-original ac-
cessories and consumable material (e.g. sand-
ing pads) is also excluded. Complaints will only
be acknowledged if the equipment has not been
dismantled before being sent back to the suppli-
ers or to an authorised Festool customer support
workshop. Store the operating instructions, safety
notes, spare parts list and proof of purchase in a
safe place. In addition, the manufacturer's current
warranty conditions apply.
Note
We reserve the right to make changes to the tech-
nical data contained in this information as a result
of ongoing research and development work.
REACH for Festool products, their accessories
and consumables
REACh is a European Chemical Directive that
came into effect in 2007. As "downstream users"
and product manufacturers, we are aware of our
duty to provide our customers with information.
We have set up the following website to keep you
updated with all the latest news and provide you
with information on all the materials used in our
existing products: www.festool.com/reach
17