Display Settings - Kenwood KDC-BT365U Mode D'emploi

AUDIO SETTINGS
X ' OVER
TWEETER FRQ 1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ/ 10KHZ/ 12.5KHZ:
Adjusts the crossover frequency for the tweeter speaker.
GAIN LEFT –8 to 0: Adjusts the output volume of the left tweeter.
GAIN RIGHT –8 to 0: Adjusts the output volume of the right tweeter.
FRONT HPF F - HPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/ 150HZ/
180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency for the selected
speakers (high pass filter). ; THROUGH: All signals are sent to the selected
speakers.
F - HPF SLOPE –6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope.
(Selectable only if a setting other than [THROUGH] is selected for [F - HPF FRQ].)
F - HPF GAIN –8 to 0: Adjusts the output volume of the selected speaker.
REAR HPF R - HPF FRQ (Refer FRONT HPF settings above.)
R - HPF SLOPE
R - HPF GAIN
SUBWOOFER SW LPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/ 150HZ/
LPF 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency for the subwoofer (low
pass filter). ; THROUGH: All signals are sent to the subwoofer.
SW LPF SLOPE –6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope.
(Selectable only if a setting other than [THROUGH] is selected for [SW LPF FRQ].)
SW LPF PHASE REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer output to be
in line with the speaker output for optimum performance.
SW LPF GAIN –8 to 0: Adjusts the output volume of the subwoofer.
• (For /
[SUB-W LEVEL]/ [SUBWOOFER SET]/ [SUBWOOFER] of [SPEAKER SIZE]/ [SUBWOOFER LPF] of [X ' OVER] is
selectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 4)
• [SUB-W LEVEL]/ [SUBWOOFER] of [SPEAKER SIZE]/ [SUBWOOFER LPF] of [X ' OVER] is selectable only if
[SUBWOOFER SET] is set to [ON].
• [TWEETER], [REAR HPF] and [SUBWOOFER LPF] of [X ' OVER] is selectable only if a setting other than [NONE] is
selected for [TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE].
22
)

DISPLAY SETTINGS

(For / /
Set the dimmer
Press and hold DISP (DIMMER) to turn on or off the
dimmer.
• If you have set [DIMMER TIME] ( 23), it will be canceled
once you press and hold this button.
Other settings
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [DISPLAY], then
press the knob.
3 Turn the volume knob to select an item ( 23),
then press the knob.
4 3
Repeat step until the desired item is selected/
activated or follow the instructions stated on the
selected item.
5
Press and hold to exit.
To return to the previous setting item, press
)
.