Bosch GFA 18-H Professional Notice Originale page 14

OBJ_BUCH-3261-001.book Page 14 Friday, January 26, 2018 7:45 PM
14 | English
Technical Data
Hammer adapter with auxiliary handle
Article number
Cordless Screwdriver
Article number
Rated speed
Impact frequency at rated speed
Max. drilling dia. in concrete
Weight according to EPTA-Procedure
01:2014
Sound power level
Sound pressure level
Uncertainty
Vibration total value
Uncertainty
*depending on the battery pack being used
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-6.
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-6.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Changing the Tool
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
1 609 92A 3YJ | (26.1.18)
GFA 18-H, GHA FC2 GFA 18-H, GHA FC2
2 609 199 816
GSR 14.4 V-EC
FC2
3 601 JE1 0..
-1
min 0 –1600
-1
min 0 –4500
mm 10
kg 2.4 – 2.9*
dB(A) 97
dB(A) 87
dB 3
m/s2 12
m/s2 1.5
Mounting the Adapter (see figure A)
Remove the application tool.
Insert the adapter into the mounting 1. Turn the locking ring
10 until it audibly engages.
Inserting the Application Tool into the Adapter
GFA 18-H, GHA FC2 (see figure B):
Insert the application tool all the way into the mounting 1.
Removing
GFA 18-H, GHA FC2 (see figure C):
Push back the locking sleeve and remove the tool.
Changing the position of the auxiliary handle (see
figure H)
You can swivel the auxiliary handle 9 in order to achieve a safe
work posture that minimises your fatigue.
– Turn the bottom part of the auxiliary handle 9 in antclock-
wise direction and swivel the auxiliary handle 9 to the re-
quested position. Then retighten the bottom part of the
auxiliary handle 9 by turning in clockwise direction.
Adjusting the Drilling Depth (see figure I)
The desired drilling depth X can be specified with the depth
stop.
– Press the button for the depth stop adjustment and insert
the depth stop into the auxiliary handle 9.
The knurled surface of the depth stop must face downward.
– Insert the SDS-plus drilling tool to the stop into the SDS-
plus tool holder. Otherwise, the movability of the SDS-plus
drilling tool can lead to incorrect adjustment of the drilling
depth.
– Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with
the desired drilling depth X.
GFA 18-H, GHA FC2
2 609 199 816 2 609 199 816
GSR 18 V-EC
FC2 GSR 18 V-60FC
3 601 JE1 1.. 3 601 JG7 1..
0 –1700 0 –1900
0 –4800 0 –5400
10 10
2.4 – 2.9* 2.4 – 2.9*
97 91.5
87 80.5
3
14
1.5 1.5
Bosch Power Tools
3
7