Assembly / Before Commissioning; Start Up; Cleaning; Transport - Scheppach HW2500 Traduction Des Instructions D'origine

• Include our item number, the device model and
year of manufacture in your order.
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts!
m DANGER
There is a risk of swallowing and suffocation!

8. Assembly / Before commissioning

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
1. Ensure that the safety bolts (5) are inserted in the
pump.
2. Knock the clamping sleeve (6) into the axle (4) us-
ing a hammer. (Fig. E)
3. Place the drawbar (2) into the pump and slide the
axle (4) through the drawbar (2) ensuring that the
chain (7) is hanging out behind the drawbar. (Fig.
F)
4. Insert the chain (7) through the hole in the axle
(4). (Fig. G)
5. Knock the second clamping sleeve (6) on the oth-
er side into the axle (4) using a hammer. (Fig. F)
The clamping sleeve (6) must protrude from both
sides of the axle (4). (Fig. E)
6. Push the drawbar (2) downwards and carefully
pull out the safety bolts (5). (Fig. I)
7. Push the lever (A) down and push the guide pin of
the chain (7) through the lever (A) guide. (Fig. J)
8. Secure the guide pin by tightening the nut (B).

9. Start up

Ensure that the machine is installed completely and
properly. Before each use, always check:
• The machine for possible damage,
• Whether all screws are tightened,
• The hydraulic oil for leaks
• The oil level
• Visibility of all labels
9.1 Lever positions (Fig. K)
The operating lever (1) installed in the drawbar has 3
positions:
• To lower the fork, lift the operating lever (1) up (pos.
"down"). As soon as it is released, it springs back
into the neutral position.
• The fork position "neutral" is used if the pallet truck
is moved. In this position, the drawbar can move up
and down without the fork moving.
16 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• To lift the fork, push the operating lever (1) down
(pos. "up"). The fork (3) is lifted by the up and down
movement of the drawbar (2).
m Attention! Make sure that the goods are fully
on the pallet. The load-bearing capacity of the
device must not be exceeded!

10. Cleaning

• We recommend that you clean your device after
each use.
• Wipe dust off the machine from time to time with
a cloth.
• Clean the unit regularly with a damp cloth and some
soft soap. Do not use cleaning agents or solvents;
they may damage the plastic parts of the appliance.
Make sure that no water can get inside the unit.

11. Transport

In order to transport the pallet truck, secure the de-
vice against rolling away. Remove course dirt from
the device.

12. Storage

Bring the pallet truck forks down in order to relieve
the stored energy. This leads to a longer service life
of the seals and valves.
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the tool in its original packaging.
Cover the tool in order to protect it from dust and mois-
ture.

13. Maintenance

m ATTENTION!
Only use spare parts approved by us!
m ATTENTION!
Before working on the hydraulic system, relieve
the devices to depressurise the system!
13.1 Ventilation of the hydraulic unit
Air may build up in the hydraulic system due to op-
eration or pumps. This can lead to the fork not lifting
when pumping. To rectify this problem, keep the op-
erating lever (1) in the "down" position and move the
drawbar up and down several times.

13.2 Lubrication

Lubricate all bearings and axles with the appropriate
lubricant.