Makita XSL01 Manuel D'instruction page 13

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Loosen two clamp screws which secure the slide
poles counterclockwise so that the carriage can
slide freely. Secure the workpiece with the proper
type of vise. Pull the carriage toward you fully.
Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
Press
the
handle
CARRIAGE TOWARD THE GUIDE FENCE AND
THROUGH THE WORKPIECE. When the cut is
completed, switch off the tool and WAIT UNTIL
THE BLADE HAS COME TO A COMPLETE STOP
before returning the blade to its fully elevated
position.
WARNING:
Whenever performing a slide cut, first pull the
carriage full towards you and press the handle
all the way down, then push the carriage
toward the guide fence. Never start the cut with
the carriage not pulled fully toward you. If you
perform the slide cut without the carriage pulled
fully toward you unexpected kickback may occur
and serious personal injury may result.
Never attempt to perform a slide cut by pulling
the carriage towards you. Pulling the carriage
towards you while cutting may cause unexpected
kickback resulting in possible serious personal
injury.
Never perform the slide cut with the handle locked
in the lowered position.
Never loosen the knob which secures the
carriage while the blade is rotating. A loose
carriage while cutting may cause unexpected
kickback resulting in possible in serious personal
injury.
3.
Miter cutting
Refer to the previously covered "Adjusting the
miter angle".
4.
Bevel cut
011246
Loosen the lever and tilt the saw blade to set the
bevel angle (Refer to the previously covered
"Adjusting the bevel angle"). Be sure to retighten
the lever firmly to secure the selected bevel angle
safely. Secure the workpiece with a vise. Make
down
and
PUSH
sure the carriage is pulled all the way back toward
the operator. Switch on the tool without the blade
making any contact and wait until the blade attains
full speed. Then gently lower the handle to the fully
lowered position while applying pressure in parallel
with the blade and PUSH THE CARRIAGE
THE
TOWARD THE GUIDE FENCE TO CUT THE
WORKPIECE. When the cut is completed, switch
off the tool and WAIT UNTIL THE BLADE HAS
COME TO A COMPLETE STOP before returning
the blade to its fully elevated position.
WARNING:
After setting the blade for a bevel cut, before
operating the tool ensure that the carriage and
blade will have free travel throughout the entire
range of the intended cut. Interruption of the
carriage or blade travel during the cutting operation
may result in kickback and serious personal injury.
While making a bevel cut keep hands out of the
path of the blade. The angle of the blade may
confuse the operator as to the actual blade path
while cutting and contact with the blade will result
in serious personal injury.
The blade should not be raised until it has
come to a complete stop. During a bevel cut the
piece cut off may come to rest against the blade.
If the blade is raised while it is rotating the cut-off
piece maybe ejected by the blade causing the
material to fragment which may result in serious
personal injury.
NOTICE:
When pressing down the handle, apply pressure in
parallel with the blade.
perpendicularly to the turn base or if the pressure
direction is changed during a cut, the precision of
the cut will be impaired.
5.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter
angle is being cut on a workpiece. Compound
cutting can be performed at the angle shown in the
table.
Miter angle
Left and Right 45
Right 50
Right 55
Right 57
006393
When performing compound cutting, refer to
"Press cutting", "Slide cutting", "Miter cutting" and
"Bevel cut" explanations.
13
If a force is applied
Bevel angle
Left 0 - 45
Left 0 - 40
Left 0 - 30
Left 0 - 25

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

011234

Table des Matières