DeWalt DWE7491 Guide D'utilisation page 15

Fig. VV
Featherboard Construction (Fig. WW, XX)
Featherboards are used to keep the work in contact with the fence and table, and help prevent
kickbacks. Dimensions for making a typical featherboard are shown in Figure WW. Make
the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the
featherboard to the fence and table so that the leading edge of the featherboard will support the
workpiece until the cut is complete (Fig. XX). An 8" (203 mm) high flat board can be clamped to
the rip fence and the featherboard can be clamped to the 8" (203 mm) high board.
Fig. WW
24" (610 mm)
The kerf
4"
should be
(102 mm)
about 1/4"
(6.4 Mm) apart

WARNING: Use featherboards for all non thru-sawing operations where the blade guard
assembly, anti-kickback assembly and riving knife cannot be used. Always replace the
blade guard assembly, anti-kickback assembly and riving knife when the non thru-
sawing operation is complete. Make sure the featherboard presses only on the portion of
the workpiece in front of the blade.
Fig. XX
MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect
it from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
47
49
5" (127 mm)
Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
D WALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-D
e
(1-800-433-9258) or visit our website: www.dewalt.com.
· DWE7402DI Dado Throat Plate
· DW7670 Stacked Dado Set
· DWE74911 Rolling Table Saw Stand
· DWE74912 Scissor Leg Stand
Repairs

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement, when applicable) should be
performed by a D WALT factory service center or a D
e
use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help you obtain more efficient warranty
3/4"
service in case there is a problem with your product.
(20 mm)
COnFiRMATiOn OF OWnERshiP: In case of an insurance loss, such as fire, flood or theft,
•
your registration of ownership will serve as your proof of purchase.
FOR YOUR sAFETY: Registering your product will allow us to contact you in the unlikely
•
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
e
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
to accessories or damage caused where repairs have been made or attempted by others. THIS
LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply to you. This warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
e
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
e
during the first year after purchase.
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for
a full refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning labels become illegible or are missing,
call 1-800-4-D WALT (1-800-433-9258) for a free replacement.
e
WALT, have not been tested
e
WALT authorized service center. Always
e
WALT (1-800-433-9258). This warranty does not apply
e
WALT tools are covered by our:
1 YEAR FREE sERViCE
90 DAY MOnEY BACK gUARAnTEE
WALT Power Tool, Laser, or
e
English
WALT
e
13