Specific Safety Instructions For Wood Lathes; Residual Risks - LEMAN TAB050 Manuel D'utilisation

- IMPROPER ELECTRICAL CONNECTION of the equipment grounding conductor can result in risk of electric
shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding
conductor. DO NOT connect the equipment grounding conductor to a live terminal if repair or replacement of the
electric cord or plug is necessary.
- CHECK with a qualified electrician or service personnel if you do not completely understand the grounding
instructions, or if you are not sure the tool is properly grounded when installing or replacing a plug.
- USE ONLY A 3-WIRE EXTENSION CORD THAT HAS THE PROPER TYPE OF A 3-PRONG GROUNDING
PLUG THAT MATCHES THE MACHINE'S 3-PRONG PLUG AND ALSO THE 3-POLE RECEPTACLE THAT
ACCEPTS THE TOOL'S PLUG.
- REPLACE A DAMAGED OR WORN CORD IMMEDIATELY.
- THE USE OF AN EXTENSION CORD WITH THIS MACHINE IS NOT RECOMMENDED. For best power and
safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the supplied cord length
of the machine.
- If an extension cord needs to be used, it should only be for a limited operation of the machine. The extension cord
should be as short as possible in length.
- Check extension cords before each use. If damaged replace immediately. Never use a tool with a damaged cord,
since touching the damaged area could cause electrical shock, resulting in serious injury.
- Use a proper extension cord. Other extension cords can cause a drop in line voltage, resulting in a loss of power
and overheating of tool. When operating a power tool outdoors, use an outdoor extension cord and rated for
outdoor use and reduce the risk of electric shock.
- Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools
or other obstructions while you are working with your power tool.

2.3 Specific safety instructions for wood lathes

- This machine is intended for the shaping, smoothing and finishing of natural, solid woods. The permissible
workpiece dimensions must be observed (see Technical Specification). Any other use not as specified, including
modification of the machine or use of parts not tested and approved by the equipment manufacturer can cause
unforeseen damage.
- Do not operate this machine until you have read all of the following instructions.
- Do not attempt to operate this machine until it is completely assembled.
- Do not turn ON this machine if any pieces are damaged or missing.
- This machine must be properly grounded.
- If you are not familiar with the operation of the machine, obtain assistance from a qualified person.
- Always wear approved, safety protective eyewear and hearing protection when operating this machine.
- Always wear a dust mask and use adequate dust collection and proper ventilation.
- Do not wear loose clothing or jewelry when operating this machine. Keep long hair tied back.
- Always make sure the power switch is in the OFF position prior to plugging in the machine.
- Always make sure the power switch is in the OFF position and the machine is unplugged when doing any
cleaning, assembly, setup operation, or when not in use.
- Use only sharp lathe tools. Dull tools can damage your work and are unsafe to use.
- When turning between centers, make sure the headstock and tailstock are snug against the workpiece.
- When face plate turning, rough-cut the workpiece close to the finished shape before screwing it to the face plate.
- Never jam tools into the workpiece or take too big of a cut.
- Make sure there are no loose knots, nails, staples, dirt or foreign objects in the workpiece to be turned.
- Wood should not be warped, cracked or have improperly made or cured glue joints.
- Test spin the workpiece to ensure that it does not hit the lathe bed or tool rest before turning on the lathe.
- Start the lathe at slow speeds to check the settings, and then increase the speed to your desired level for
working.
- Low speeds are best for roughing stock, and for long or large diameter workpieces.
- If excessive vibration occurs, stop the lathe to check the workpiece settings between centers or on face plates.
- For sanding or applying finishes, remove the tool rest from the machine. Use low speeds to avoid heat build-up.
- Do not engage the spindle lock (16) when the lathe is turning, and be sure to disengage the spindle lock when
done working to avoid damage to the machine next time the lathe is turned on.
- Never stop the machine by grabbing the workpiece, faceplate or hand wheel. Let the machine stop on its own.
- The use of any accessories or attachments not recommended may cause injury to you and damage your
machine.
- Remove material or debris from the work area. Keep the floor and work area neat and clean.
- Keep these instructions for future reference.

2.4 Residual risks

Despite observance of all the safety regulations, and use according to the rules described in this manual, residual
risks may still be present, among which the most recurring are:
GB
25