Safety Warnings For Drills; Product Description And Specifications - Berner BRD-HT Notice Originale

ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of chil-
u
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools and accessories. Check
u
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unex-
pected situations.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.

Safety Warnings for Drills

Safety instructions for all operations
Use auxiliary handle(s). Loss of control can
u
cause personal injury.
Hold the power tool by insulated gripping sur-
u
faces, when performing an operation where
the cutting accessory or fasteners may con-
tact hidden wiring or its own cord. Cutting
accessory or fasteners contacting a "live" wire
may make exposed metal parts of the power
tool "live" and could give the operator an elec-
tric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the max-
u
imum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to ro-
tate freely without contacting the workpiece,
resulting in personal injury.
Always start drilling at low speed and with
u
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if al-
12 | English
lowed to rotate freely without contacting the
workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit
u
and do not apply excessive pressure.Bits can
bend causing breakage or loss of control, res-
ulting in personal injury.
Additional safety warnings
Switch the power tool off immediately if the
u
application tool becomes blocked. Be pre-
pared for high torque reactions which cause
kickback. The application tool becomes
blocked when it becomes jammed in the work-
piece or when the power tool becomes over-
loaded.
Hold the power tool securely. When tightening
u
and loosening screws be prepared for tempor-
arily high torque reactions.
Secure the workpiece. A workpiece clamped
u
with clamping devices or in a vice is held more
secure than by hand.
Use suitable detectors to determine if utility
u
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
Always wait until the power tool has come to
u
a complete stop before placing it down. The
application tool can jam and cause you to lose
control of the power tool.
Products sold in GB only:
Your product is fitted with an BS 1363/A ap-
proved electric plug with internal fuse (ASTA ap-
proved to BS 1362).
If the plug is not suitable for your socket outlets, it
English
should be cut off and an appropriate plug fitted in
its place by an authorised customer service agent.
English
The replacement plug should have the same fuse
rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inser-
ted into a mains socket elsewhere.
Product Description and
Specifications
English
Please observe the illustrations at the beginning
of this operating manual.
English
English
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or ser-
ious injury.
1 609 92A 5AJ • 8.10.19