Programming - Brandt BWT6010E Guide D'installation / Guide D'utilisation

4 / PROGRAMMING YOUR MACHINE

•PROGRAMMING

Nature of the washing and the
temperature
Spin speed setting
•Programming a washing cycle:
— Turn the selector 1 to choose the most suitable programme and washing temperature for
the type of fabric to be washed.
NB: Turning the selector to any position other than "O" provides power to the machine.
2
— Using the selector , choose:
- Either a suitable spin speed for your type of washing.
The spin speed is automatically restricted in the "Synthetics" and "Wool / Delicates"
programmes.
- Or drip dry.
The cycle will finish with a gentle spin at 100 rpm.
- Or stop with tub full of water.
Your machine will stop with the tub full of water before the final spin.
— Use the buttons 4 to select any options you wish.
— Select immediate start by pressing "Start/Pause"
— ... Or use the selector 3
hours and then press "Start/Pause"
•Adding or removing an item during the cycle
— Press the "Start/Pause" button
— Add or remove the items of laundry * .
— Press the "Start/Pause" button
(*) The time the lid remains locked depends on the temperature inside the machine and,
for safety reasons, may take several minutes if you are interrupting a cycle at more than
40°C.
NB: If you have selected a delayed start, you can access the drum instantly at any time in the
period before the washing cycle starts without having to interrupt and restart the cycle.
•Cancelling while programming, washing or during a pause:
to the " O " position.
— Set the selector 1
This can be done at any time during the cycle or during programming, or even during a pause.
NB :
- In all cases, after cancelling you must reprogramme everything from the start.
- If you have cancelled during the washing phase, remember to empty the water, if necessary.
•End of the cycle:
NB: After spinning, some models automatically position the drum opening at the top to
provide easy access to the washing. This operation lasts at most 3 minutes.
— Then, the "Stop" light comes on permanently, indicating that the cycle is over.
Set the selector 1 to the "O" position.
You can now open the lid and remove your washing.
For more details on the various functions, please refer to the sections "DETAILS OF THE PROGRAMMES" and "DETAILS OF THE OPTIONS".
Information :
After a power failure, when the power is restored, the washing cycle automatically resumes at the point where it was interrupted.
Cycle progress
1
2
Delayed start setting
(depending on the model)
5 ...
(depending on the model) to select starting delayed by 1 to 19
5 .
5 to interrupt the cycle.
5 to restart the cycle.
Start/Pause
A
5
3
4
Options
(impossible during spin):
15
Information:
All the buttons are on micro-
switches and do not remain depressed.
In any case, the "Start/Pause" button
cannot cancel a programme.
Important :
Before starting your machine,
check that the power cable is plugged
in and the water tap is open. Also
ensure that the drum doors are closed
correctly and the machine's lid is shut.
During the "End of Cycle" phase, any
action on one of the controls (the
selectors or the buttons) returns you to
"Programming" mode. As a safety
measure, when the cycle is over, we
recommend that you unplug the power
cable and turn off the water tap.
Indicator lights and position of the selectors
(Wash) light flashing
If you have selected rinse only or spin only,
it is the light / (Rinse/Spin) that flashes
Selector 2
- Position " 800 " for example
- Position " 100 "
- Position " "
Light(s) for the option(s) selected
(Wash) light permanently lit
(The lights A illuminate in succession to show
which phase the cycle is at)
The lights A flash in succession until the cycle
effectively starts
Light A flashing
Light A permanently lit
Selector 1 set to "O"
All the lights unlit
The "Stop" light is permanently lit
EN
on