Electronic Control Setup; General User Information - Whirlpool 3LCGD9100 Instructions D'installation

Masquer les pouces Voir aussi pour 3LCGD9100:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD is present everywhere. ESD may damage or weaken the
electronic control assembly. The new control assembly may
appear to work well after repair is finished, but failure may
occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green
I
earth connection point or unpainted metal in the appliance.
Touch your finger repeatedly to a green earth connection point
or unpainted metal in the appliance.
Before removing the part from its package, touch the
I
anti-static bag to a green earth connection point or
unpainted metal in the appliance.
Avoid touching electronic parts or terminal contacts; handle
I
electronic control assembly by edges only.
When repackaging failed electronic control assembly in
I
anti-static bag, observe above instructions.

ELECTRONIC CONTROL SETUP

-OR-
EU - DECLARATION OF CONFORMITY
CE - DECLARATION DE CONFORMITE
BAUKNECHT HAUSGERÄTE GmbH, D-73614 Schorndorf
WE (nous):
WHIRLPOOL EUROPE S.r.l I-21025 COMERIO
representing (représentant):
declare under our sole responsibility that the product
déclarons sous notre propre responsabilité que le produit
Whirlpool
dryer
(sèche-linge) :
to which this declaration relates is in conformity with the following standard(s) or other
normative document(s)
auquel se référe cette déclaration est conforme aux normes suivantes ou autres documents normatifs
EN 60335-1:2002+A1+A2+A11+A12+A13
EN 60335-2-11:2003+A1+A2
EN 12752-1:1999
EN 62233:2008
EN ISO 10472-1:2008
EN ISO 10472-4:2008
EN 55014-1:2006
EN 55014-2:1997+A1:2001
EN 61000-3-11:2000
EN 61000-3-12:2005
following the provisions of Directive(s):
suivant les prévisions des Directives :
2009/142/EC EUROPEAN GAS APPLIANCE DIRECTIVE
2006/95/EC LOW VOLTAGE DIRECTIVE
2004/108/EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE
Electro-magnétique)
2006/42/EC MACHINERY DIRECTIVE
Schorndorf, 29.04.2010
Place and date:
lieu et date :

GENERAL USER INFORMATION

"out of order" showing in display
This condition indicates the dryer is inoperative. Diagnostic or failure
code will follow the scrolling message.
'0 Minutes' showing in display
This condition indicates the dryer cannot be operated until normal
operation is restored by opening and closing the door. If a door
switch fails, it must be replaced before normal operation can be
restored.
Cold Start (initial first use)
Dryer is programmed at the factory as follows:
45 minutes dry time.
I
Warm Start (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, 'RESELECT CYCLE' will flash
in the display. This is to indicate the need for a fabric setting
button to be pressed to restart dryer.
Dryer is pre-set for free cycle operation so it can be run without payment.
DISPLAY
After the dryer has been installed and plugged in, the display will
show '0 minutes.'
Once the dryer has been plugged in and the dryer door opened
and closed, the display will flash 'SELECT CYCLE'.
3LCGD9100
(CEE Directive Basse Tension)
(CEE Directive Compatibilité
represented by
Roberto Mottura
Director PDC, FC
Name and signature of authorised person
Nom et signature de la personne autorisée
13

Publicité

Table des Matières
loading

Table des Matières