Transportation And Storage; Cleaning And Maintenance - Royal Catering RCWM-1300-RE Manuel D'utilisation

VIII. MACHINE OPERATION - BASICS
1
2
Description of the device:
3
1.
2.
4 3.
4.
5
5.
6
6.
8
7.
7
8.
Using the device:
1. Assemble the device, as shown in the photo. Place the handle in the desired position and tighten the
nut.
2. Move the main switch to the "0" position and thoroughly clean the device, particularly the heating
plates.
3. Insert the plug into a socket and move the main switch to the "I" position, the orange indicator lamp,
signalling that heating is in progress, will go on.
4. The display shows digits indicating the heating time. In order to set the heating time, press and hold
the "+" buttons (in order to expand the heating time) or the "-"button (in order to reduce it), then
press the "START/STOP" button on the right side of the panel to set the required time. The two
digits on the right are the numbers of seconds, the two digits on the left are the number of minutes.
Next, set the required temperature on the display. In order to do so, press and hold the "START/
STOP" and "SET" buttons simultaneously (the latter is used to change the time and temperature set-
tings), then use the "+" and "-" buttons to set the required temperature (the temperature is displayed
in oC). The device has an integrated memory, which stores the working temperature and time, which
means it is not necessary to set these parameters before every use of the device.
5. Once the temperature and time are set, you can start the timer. To do so, use the "SET" button to
choose the time on the display and press the "START/STOP" button.
6. The orange indicator light means that the device is heating up. Once the temperature reaches the
pre-set value, a green indicator light on the display will go on. The device maintains the temperature
automatically. Reaching the maximum temperature of the device (230oC) takes about 15 minutes.
7. Next, carefully open the top cover by holding the lever (grease the heating plates if necessary), spread
an appropriate amount of pre-made dough on the lower heating plate, close the device and turn the
lever clockwise in order to spread the dough over the heating elements. Closed heating plates may be
rotated by the maximum angle of 180o.
8. In order to remove the finished waffles, put the heating plates in the initial position and carefully open
the top lid (keep in mind the high temperature).
9. Remove the waffle. Be careful not to damage the heating plates when removing the waffles. Caution!
The first few waffles should not be eaten.
10. In order to make more waffles, follow the described procedures and check the time. When the time
on the display runs out, the device will emit a distinctive, continuous beep; in order to turn it off,
press the "START/STOP" button or turn it off with the main switch.
9
Handle
Upper heating plate
Rotary mounting
Lower heating plate
Metal enclosure
Tray
Control panel with display
Main switch
Rev. 10.02.2017
11. After you have finished with the preparation of the waffles, move the switch to the "0" position and
disconnect the power supply by removing the plug from the socket.
12. Once the device has cooled down, clean it thoroughly.
CAUTION: before the first use, be sure to thoroughly clean and grease the heating plates, then heat them
up without dough. As the device heats up, the smoke can develop slowly – which is perfectly normal. You just
need to ensure sufficient ventilation. After a few minutes, turn the device off and wait for it to cool down,
then grease the heating plates – the device is ready for work.
IX. TRANSPORTATION AND STORAGE
During transport, the machine should be protected from shaking, crashing and turning upside down. Store it
in a properly ventilated place with dry air and without any corrosive gas.
X. CLEANING AND MAINTENANCE
• Always unplug the device before cleaning the equipment. Disconnect the device from the electricity
when it is not in use. Let the device cool down before cleaning it.
• Use only cleaner without corrosive substances to clean the surface.
• After each cleaning, all the elements must be carefully dried and secured by greasing the heating plates.
• Store the unit in a dry, cool place, free from moisture and direct exposure to sunlight.
• Never clean the device with a pressurized water-jet, industrial cleaners, and brushes or any other type
of cleaning utensil that could damage the surface of the appliance.
XI. REGULAR CONTROL OF THE DEVICE
Check regularly the device to see if it presents any damages. If there is any damage, please stop using the
device. Please contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare the following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, take a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give a
detailed and precise description of the matter. Avoid ambiguous formulations like "the device does not
heat", which may mean either that it does not heat enough or that it does not heat at all. The more
detailed your information, the better the customer service will be able to solve your problem rapidly
and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to a
loss of warranty!
Rev. 10.02.2017 10