Technical Data; Service Department - elem ASB40LI-2A Traduction Des Instructions D'origine

STORAGE
_ Thoroughly clean the whole machine and its
accessories.
_ Store it out of the reach of children, in a stable and
secure position, in a cool and dry place, avoid too
high and too low temperatures.
_ Protect it from exposure to direct sunlight. Keep it
in the dark, if possible.
_ Don't keep it in plastic bags to avoid humidity
build-up.
Battery storage
_ Store your batteries in a cool area. Optimal
temperature for storing your Li-ion
battery for longer term is 2°C. (capacity loss wil l
only be 6% / year (compared to 20% at 25°C)).
Never store batteries in discharged condition.
_ It is better for Li-ion batteries to recharge them
frequently. Optimal long time
storage charge for your Li-ion battery is at 40% of
their capacity.

TECHNICAL DATA

Rated voltage
Rotation speed
Max air speed
Max suction capacity
Capacity of collection bag
Weight
Noise emission values measured according to
relevant standard.
Blower mode
L 77.4 dB(A)
PA
L 90.49 dB(A)
WA
Vacuum mode
L 80.5 dB(A)
PA
L 93.69 dB(A)
WA
Guaranteed sound power level
The sound power pressure may
exceed 85 dB(A), in this case
individual hearing protection
Weighted root mean square acceleration according
to relevant standard. :
Blower mode : , a = 7.06,k=1.5m/s
h
Vacuum mode :a = 5.951,k=1.5m/s
h
k=1.5m/s 2
40 V Max.
2x20V .Max.
6000-12000 min -1
230km/h
8m³/min
45L
3.2kg
K = 2.5 dB(A)
K = 1.99 dB(A)
K = 2.5 dB(A)
K = 0.99 dB(A)
L 96 dB(A)
WA
ATTENTION !
must be worn.
2
2
The declared vibration total value has
been measured in accordance with a standard
test method and may be used for comparing one
tool with another that the declared vibration total
value may also be used in a preliminary
assessment of exposure.
A warning that the vibration emission
during actual use of the power tool can differ
from the declared total value depending on the
ways in which the tool is used and of the need to
identify safety measures to protect the operator
that are based on an estimation of exposure in
the actual conditions of use (taking account of
all parts of the operating cycle such as the times
when the tool is switched off and when it is
running idle in addition to the trigger time).

SERVICE DEPARTMENT

_ Damaged switches must be replaced by our after-
sales service department.
_ If replacing the power cord is necessary, it
should be done by the manufacturer or his agent
to avoid a hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions
concerning maintenance and repair of your product
as well as spare parts. Exploded views and
information on spare parts can also be found
under:www.eco-repa.com
ELEM GARDEN TECHNIC application service team
will gladly answer questions concerning our
products and their accessories : sav@eco-repa.com
STORAGE
• Switch the machine off and do not touch any
moving, dangerous parts. Wait until the movement
has stopped completely and the device has cooled
down.
• when you inspect the machine for damage;
if you are replacing or repairing damaged parts;
if you check for loose parts and tighten them;
• Do not allow processed material to accumulate in
the ejection zone as this may prevent proper
ejection and cause the material to be reintroduced
back through the feed opening.
Battery storage
_ Store your batteries in a cool area. Optimal
temperature for storing your Li-ion
battery for longer term is 2°C. (capacity loss wil l
only be 6% / year (compared to 20% at 25°C)).
Never store batteries in discharged condition.
_ It is better for Li-ion batteries to recharge them
frequently. Optimal long time
storage charge for your Li-ion battery is at 40% of
their capacity.
30