Quick ALEPH AL 712 Manuel De L'utilisateur page 17

POS. DESCRIPTION
19 Key
20 "AL" chain fall cover
21 Screw M5x20
22 Screw M5x16
23 Screw M5x16
24 Chain fall cover support
25 Mooring rope puller
26 Spring for pressure lever
27 Mooring rope puller pin
28 Pressure lever
29 Gypsy lock spring
30 Gypsy lock lever
31 Gypsy lock lever control
32 Lever lock control safety
33 Gypsy lock pin
34 Sensor
35 Base
36 Gasket / jig Aleph
37 Stud
38 Gearbox flange gasket
Top TG50
39 Gearbox flange gasket
Top TG60
40 Gearbox 1000W Quick TG50
41 Gearbox 1500W Quick TG70
42 Washer
43 Spring washer
44 Nut
45 Washer
46 Self-locking nuts
47 O-ring
48 O-ring
49 Key
50A Electric motor 700W 12V
50B Electric motor 700W 24V
50C Electric motor 1000W 12V
50D Electric motor 1000W 24V
50F Electric motor 1500W 12V
50G Electric motor 1500W 24V
51A Motor casing watertight 700W
51B Motor casing watertight 1000W
52 Grommet 1000W
53 Terminal board cover 1000W
54 Screw
55 Bottom gasket 1000W
56 Bottom protec cover 1000W
57 Cable outlet
58 Insert for manual anchor weighing PDRM10000000
59 Bush drum
60 O-ring
ALEPH 700/1000/1500W - REV003A
CODE
MBH0807080X0
PDCCCAL00000
MBV0520MXCE0
Quick
MBV0516MXSC0
MBV0516MXSC0 ant to marine environments. In any case, any salt deposits
PDSCCCAL0000
on the outside must be removed periodically to avoid corro-
MMSTTC10AL00
sion and damage to the equipment.
MMTND10AL000
The parts where salt may have built up should be washed
MBSC05040A00
thoroughly with fresh water.
PDLVT10AL000
MMBLBRATC000
Once a year, the drum and the gypsy are to be taken apart
MSH10ATCX000
as follows:
MSVLBBATCX00
PDSCLVBB0000
DRUM VERSION
MSVPR10ATC00
Use the handle (1) to loosen the bush (2); pull off the drum
SAKREED00000
(6) and the top clutch cone (7); loosen the fixing screws (10)
SGMSC15AL000
PGBSG10AL000 of the rope/chain stripper (11) and remove it. Pull off the
MBP080807X00
gypsy (8).
PGFLRDTG5000
NO-DRUM VERSION
Use the handle (1) to loosen the bush (2) and the screws (5);
PGFLRDTG6000
to remove the gypsy cover (4); and the top clutch cone (7);
SLMR10TG5000
loosen the fixing screws (10) of the rope/chain stripper (11)
SLMR15TG7000
MBR08X000000 and remove it. Pull off the gypsy (8).
MBR08XDE0000
MBD08MXEN000
Clean all the parts removed to avoid corrosion, and grease
MBR061815X00
the shaft thread (17 or 18) and the gypsy (8) where the
MBD06MXET000
clutch cones rest (7 and 9) (use grease suitable for marine
-
environment).
-
MBH050515F00
Remove any oxide deposits from the terminals of the elec-
EMF071200000
tric motor and the contactor unit; grease them.
EMF072400000
EMF101200000
EMF102400000
EMF151200000
EMF152400000
PCCCPM070000
PCCCPM100000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
SGMSDCPAL100
PGR031650000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17 17