Making Manual Settings; Selecting The Menu Language; Removing Registered Networks; Resetting The Unit To Its Factory Settings - IMG STAGELINE WAP-200 Mode D'emploi

The three fields ,
BKSP OK
have the following functions:
– (Backspace) delete last
BKSP
character
– password is complete, estab-
OK
lish the network connection
CANCEL – return to the previous menu
The position for selection is between the
special characters and the digits . Press
the knob CONTROL SELECT to execute
the function .
9) If the network access is WPS-encoded
(Wi-Fi Protected Setup), the WPS menu
will appear:
WPS menu
Push button
Pin
Skip WPS
The easiest way to establish the connection
is to use the function "Push button" . The
corresponding menu line has already been
selected . Press the knob CONTROL SELECT:
The menu "WPS Setup" will appear . The
WAP-200 will ask you to press the WPS
button at the router . The connection will
then be established . Finally, press the knob
CONTROL SELECT at the WAP-200 .
10) After the final entry required with regard
to the network has been made, the con-
nection will be established . This will be
indicated by various messages
Please wait ...
Once the network connection has been
established, the message
will appear, followed by the message
Setup wizard
Setup wizard
completed
Press SELECT to exit
Press the knob CONTROL SELECT to exit
the setup wizard – the main menu will
appear . Use the main menu or the button
MODE to select the operating mode de-
sired (chapter 4) .
Note: If the wizard fails to establish a connection
to the router (message
failed to connect
first reset the unit to its factory settings (chapter
3 .6) and then make the settings manually .
and

3.4 Making manual settings

CANCEL
All settings can also be made manually with-
out the setup wizard:
1) Press the button MENU . Independently
from the menu called up or from the cur-
rent operating mode, a menu containing
the line
pear .
2) Turn the knob CONTROL SELECT to select
the line
press the knob to confirm . The menu "Sys-
tem settings" will appear:
System settings
Equaliser
Network
Time/Date
>
Language
>
Factory reset
>
This menu can be used to make all set-
tings . Turn the knob CONTROL SELECT to
Fig. 19
select a setting and then press the knob
to confirm .
3) To return to the previous menu, press the
button BACK .
An overview of the menu structure can be
found on page 23 .

3.4.1 Selecting the menu language

Instead of English, a different menu language
can be selected:
1) In the menu "System settings" (fig . 21),
select the line
CONTROL SELECT and then press the knob
to call up the menu "Language":
Language
Connected
English
French
German
Italian
Spanish
2) Select the desired language in this menu .
Once the selection has been confirmed,
Fig. 20
the menu "System settings" will appear
in the language selected .
3) Press the button MODE (repeatedly) to
select the operating mode desired (chap-
ter 4) .
),
will ap-
System settings
and then
System settings
>
>
>
>
Fig. 21
Language with the knob
*
Fig. 22

3.5 Removing registered networks

The WAP-200 will remember the four wire-
less networks to which it was most recently
connected . When switched on, it will try to
find one of these networks and will connect
to the network found . To call up the list of
registered networks:
1) Press the button MENU .
2) Select the following:
 System settings
 Network
 Netwerk profile
3) Remove the networks that are not cur-
rent anymore from the list . Turn the knob
CONTROL SELECT to select the networks
one after the other and press the knob to
remove them . Thus, wrong connections
can be avoided .
3.6 Resetting the unit
to its factory settings
Resetting the unit to its factory settings will
also remove all stations stored, disconnect
the connection to the Internet, delete the
connection data and set the menu language
to English .
1) Press the button MENU .
2) Select the following:
 System settings
 Factory reset
3) In the following menu Proceed?
firm the reset with YES .
, con-
17