BST MEETY Mode D'emploi page 7

ENGLISH
IMPORTANT
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
DESCRIPTION
1. TAPE / CD PLAYER POWER SWITCH
This switch turns the tape player and CD player on and off so as to
preserve battery life when they are not needed.
2. TAPE PLAYER / RECORDER
See description later
3. EXTERNAL SPEAKER OUTPUT
This two RCA socket can be used to connect one or two external
speakers.
- When you plug your cable on the withe RCA socket, you
swith the internal HP off and all the sound is on the external
speaker.
When you plug your cablle on the ref RCA socket, the internal
-
HP and the external speaker are available.
4. EXTERNAL POWER SUPPLY SOCKET
This socket is used to plug an external power supply ( 18V DC ( no
provide in the package ).
5. AC SOCKET + FUSE
Plug the AC power cord into any standard AC outlet. Before
plugging this cord in, be sure the voltage of AC outlet is correct.
The fuse protect your speaker from different kinds of ac problems.
If the power amplifier is "on" and nothing lights, please verify fuse
compartment. If fuse is broken, please read it and change with a
new one of same size and values.
6. POWER SWITCH
Select the "On" position to swith the speaker on. Select the "Off"
position to switch the speaker off.
Note : When operating this switch, make sure that all controls are
set at minimum position
7. TONE CONTROL
This rotary potentiometer is used to adjust the tonality of . ( in the
left position = treble, in the right position = low )
8. TAPE / CD PLAYBACK LEVEL CONTROL
The tape/CD level adjustment can be used to adjust level of the
tape/CD signal to obtain the desired volume.
9. ECHO CONTROL
Use this rotary control to add echo effect on all the micro channels
( VHF or wired microphone ).
10. EXTERNAL SOURCE VOLUME CONTROL
The external source level adjustment can be used to adjust level
signal to obtain the desired volume.
11. TAPE REC OUTPUT
You connect a minidisc or a tape recorder to record your mix or
your meeting.
12. LINE OUT OUTPUT
The level of this output is controlled by the rotary potentiometers of
each peripherical ( VHF receivers, CD player, tape player, wired
microphones ). Connect this output to an additional power
amplififer.
13. MIC 3 LEVEL CONTROL
Use this control to adjust the level of the microphone plug in the
MIC 3 input to obtain the desired volume.
14. EXTERNAL SOURCE INPUT
This socket is an input. You can adjust the level of this input in
using the potentiometer (10) .
15. MIC 3 INPUT
Can be used to connect a microphone. Adjust the level by using
the potentiometer (13).
16. VOLUME CONTROL OF WIRED MIC 2 & WIRELESS MIC CH-2
Use this control to adjust the level of the microphone plug in the
MIC 2 & wireless MIC 2 input to obtain the desired volume.
17. MIC 2 INPUT
Can be used to connect a microphone. Adjust the level by using
the potentiometer (16).
18. MIC 1 INPUT
Can be used to connect a microphone. Adjust the level by using
the potentiometer (19).
19. VOLUME CONTROL OF WIRED MIC 1 & WIRELESS MIC CH-1
Use this control to adjust the level of the microphone plug in the
MIC 1 & wireless MIC 1 input to obtain the desired volume.
20. WIRELESS MIC CH-1 RF LED INDICATOR
Before use, please unfold the antenna to have a better receipt.
When you switch the RF microphone on, having the frequency
corresponding to the receiver, the RF led lights on.
Note : You can use the two micros at the same time because they
have two different frequencies.
21. WIRELESS MIC CH-2 RF LED INDICATOR
Before use, please unfold the antenna to have a better receipt.
When you switch the HF microphone on, having the frequency
corresponding to the receiver, the RF led lights on.
Note : You can use two micros at the same time because they
have two different frequencies.
22. MASTER VOLUME CONTROL
This controls the overall volume of the system.
23. VOICE PRIORITY SWITCH
Turn on voice priority switch, voice priority LED indicator will light.
When using microphone, music will be cut off automatically. Stop
using microphone, music will start again.
24. VOICE PRIORITY LED INDICATOR
Turn on voice priority switch, voice priority LED indicator will light.
25. POWER LED INDICATOR
When voltage is high, it lights green; When voltage is low, it lights
red.
26. BATTERY CHARGING LED INDICATOR
When battery is charging, the light is flashing in green. When
battery is fully charged, light stops flashing and maintains in green.
It is an AC power LED indicator also.
27. CD PLAYER
See description later