Technical Data; Before Starting The Equipment; Assembling The Equipment - Dexter power TS8 Traduction Des Instructions D'origine

6. Technical data

AC motor ....................................... 220-240 V ~ 50 Hz
Power consumption ........................... 1200 Watt (S1*)
.................................................... 1500 Watt (S6 25%)
Idle speed n ...............................................4800 min
0
Hard metal saw blade ..............ø 210 x ø 30 x 2,6 mm
Number of teeth .......................................................24
Riving knife thickness ......................................2.0 mm
Min. size of workpiece W x L x H ....... 10 x 50 x 1 mm
Table size..............................................485 x 445 mm
Table width extension ...........................485 x 515 mm
Table size max. . ...................................485 x 630 mm
Cutting height max. 45° ....................................45 mm
Cutting height max. 90° ....................................48 mm
Tilting saw blade .......................................... 0-45° left
Suction connection ....................................... ø 35 mm
Weight ...................................................approx. 14 kg
Machine size (with extension)
W x L x H .................................... 485 x 630 x 440 mm
*S1: Continuous operation at constant load
**S6 25% operating mode:
Continuous duty with intermittent loading (operating
time 10 min.)
In order avoid impermissible overheating of the motor,
the motor should be driven for only 25% of the operat-
ing time with the stipulated nominal power and must
then continue to run with no load for the remaining
75% of the operating time.
Noise
The total noise
termined in
EN 62841.
Sound pressure level L ........................... 87.5 dB(A)
pA
Uncertainty K .................................................... 3 dB
pA
Sound power level L ............................. 100.5 dB(A)
WA
Uncertainty K .................................................... 3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 62841.
NOTE: The specified device emissions values have
been measured in accordance with a standardised
test procedure and can be used for comparison of one
electric tool with another.
The specified device emissions values can also be
used for an initial estimation of the load.
WARNING: The noise emission values can vary from
the specified values during the actual use of the elec-
tric tool, depending on the type and the manner in
which the electric tool is used, and in particular the
type of workpiece being processed. Implement meas-
ures to protect against noise nuisance. In doing so,
-1
values were de-
accordance with
take into account the complete working process, in-
cluding the times when the electric tool is working
without load or switched off.
Suitable measures include regular maintenance and
care of the electric tool and the insertion tools, regu-
lar breaks as well as proper planning of the working
process.

7. Before starting the equipment

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
m WARNING
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be securely installed, i.e. bolt-
ed down on a workbench, base frame or similar.
Use the holes on the inner side of the frame legs
for this.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails or
screws, etc.
• Before you press the On/Off switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
identical to the mains data.
• Connect the equipment to a properly installed pro-
tective contact socket, with at least 16 A circuit
breaker.

8. Assembling the equipment

m WARNING: Disconnect the mains power plug be-
fore maintaining, resetting or assembling the table
saw.
8.1 Before assembling the equipment
• Place all parts supplied on a flat surface.
• Group equal parts.
GB | 31