Technical Data - Dexter power MS SL 8 Traduction Des Instructions D'origine

Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro­
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur­
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Safety instructions for handling batteries
1 Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated on
the battery.
Do not short­circuit batteries.
2
3 Do not charge non­rechargeable batteries.
4 Do not overcharge batteries!
5 Do not mix old and new batteries or batteries of
different types or manufacturers! Replace an entire
set of batteries at the same time.
Immediately remove used batteries from the de­
6
vice and dispose of them properly! Do not dispose
batteries with household waste. Defective or used
batteries must be recycled according to Directive
2006/66 / EC. Give back batteries and / or the device
has been offered to the collective facilities. About
disposal facilities you can inform by your municipal
or city government.
7 Do not allow batteries to heat up!
8 Do not weld or solder directly on batteries!
9 Do not dismantle batteries!
10 Do not allow batteries to deform!
Do not throw batteries into fire!
11
12 Keep batteries out of the reach of children.
13 Do not allow children to replace batteries without
supervision!
14 Do not keep batteries near fire, ovens or other
sources of heat. Do not use batteries in direct
sunlight or store them in vehicles in hot weather.
15 Keep unused batteries in the original packaging and
keep them away from metal objects. Do not mix
unpacked batteries or toss them together! This can
lead to a short­circuit of the battery and thus dam­
age, burns or even the risk of fire.
16 Remove batteries from the equipment when it will
not be used for an extended period of time, unless
it is for emergencies!
17 NEVER handle batteries that have leaked without
appropriate protection. If the leaked fluid comes into
contact with your skin, the skin in this area should be
rinsed off under running water immediately. Always
prevent the fluid from coming into contact with the
eyes and mouth. In the event of contact, please seek
immediate medical attention.
18 Clean the battery contacts and corresponding con­
tacts in the device prior to inserting the batteries:

6. Technical data

AC motor
Power
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Swivel range
Mitre cut
Saw width at 90°
Saw width at 45°
Saw width at 2 x 45°
(double mitre cut)
Protection class
Weight
Laser class
Wavelength of laser
Laser output
Laser module power
supply
* S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed
by a period at no load. Running time 10 minutes;
duty cycle is 25% of the running time.
The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
Make sure that the workpiece is always secured with
the clamping device.
Noise
Total noise values determined in accordance with EN
61029.
220 ­ 240 V ~ 50Hz
1200 Watt
S6 25%* 1500W
5000 min
­1
ø 210 x ø 30 x 2,6 mm
24
­45° / 0°/ +45°
0° bis 45° nach links
340 x 58 mm
240 x 58 mm
240 x 32 mm
II
approx. 17 kg
2
650 nm
< 1 mW
2 x 1,5 V Micro (AAA)
GB 25