RIDGID R32104 Manuel D'utilisation page 9

OPERATION
BLADE GUARD SYSTEM
See Figure 5, page 15.
The lower blade guard attached to your saw is there for
your protection and safety. Do not alter it for any reason.
If it becomes damaged, do not operate the saw until you
have the guard repaired or replaced. Always leave guard in
operating position when using the saw.
DANGER:
When sawing through work, lower blade guard
does not cover blade on the underside of work.
Since blade is exposed on underside of work, keep
hands and fingers away from cutting area. Any part
of your body coming in contact with moving blade
will result in serious injury.
WARNING:
To avoid possible serious injury, never use saw
when guard is not operating correctly. Check the
guard for correct operation before each use. The
guard is operating correctly when it moves freely,
and instantly returns to the closed position. If you
drop the saw, check the lower blade guard and
bumper for damage at all depth settings before
reuse.
If at any time the lower blade guard does not snap closed,
unplug the saw from the power supply. Exercise the lower
guard by moving it rapidly back and forth from the full open
position to the closed position several times. Normally this
will restore the guard to its normal operating condition. If
it does not correct a slow or sluggish closing lower guard,
do not use the saw. Take it to an authorized factory service
center for repair.
KICKBACK
See Figures 6 - 9, page 16.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood.
WARNING:
Release switch immediately if blade binds or saw
stalls. Kickback could cause you to lose control of
the saw. Loss of control can lead to serious injury.
To guard against kickback, avoid dangerous practices such
as the following.
 Setting blade depth incorrectly.
 Sawing into knots or nails in workpiece.
 Twisting the blade while making a cut.
 Making a cut with a dull, gummed up, or improperly set
blade.
 Supporting the workpiece incorrectly.
 Forcing a cut.
 Cutting warped or wet lumber.
 Operating the tool incorrectly or misusing the tool.
To lessen the chance of kickback, follow these safety
practices.
 Do not cut warped or wet lumber.
 Keep the blade at the correct depth setting. The depth set-
ting should not exceed 1/4 in. below the material being cut.
 Inspect the workpiece for knots or nails before cutting.
Never saw into a knot or nail.
 Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade.
 Use clean, sharp, and properly set blades. Never make
cuts with dull blades.
 Support the workpiece properly before beginning a cut.
 Use steady, even pressure when making a cut. Never
force a cut.
 Hold the saw firmly with both hands and keep your body
in a balanced position so as to resist the forces if kickback
should occur.
WARNING:
When using the saw, always stay alert and exercise
control. Do not remove the saw from the workpiece
while the blade is moving.
SETTING BLADE DEPTH
See Figure 10, page 16.
Always keep correct blade depth setting. The correct blade
depth setting for all cuts should not exceed 1/4 in. below the
material being cut. More blade depth will increase the chance
of kickback and cause the cut to be rough. For more depth
of cut accuracy, a scale is located on the elevation bracket.
NOTE: The marks on the scale refer to the actual depth of
cut (blade exposure).
 Unplug the saw.
 Pull depth lock lever upward to release. The depth lock
lever is located between the guard and handle of the saw.
 Determine the desired depth of cut.
 To select the depth of cut, hold base flat against the
workpiece. Raise or lower saw to align the desired mea-
surement on the scale with the depth arrow indicator,
located directly above the lock mechanism.
 Push down on the depth lock lever to lock the lever in
place and secure the position.
9 - English