Specified Conditions Of Use - Milwaukee WCE 65 Notice Originale

WORK ORGANIZATION
Use hearing protection, eye protection, respiratory
protection and (if necessary) gloves. At minimum, use a
class FFP2 half-face particulate mask for respiratory
protection.
Use a dust extractor to keep the workplace clean. To avoid
stirring up dust, do not sweep up dust deposits.
TRANSPORT, HANDLING AND STORAGE
Diamond cutting discs must be handled and transported
with care. Use the original packaging if possible, or use
other suitable packaging.
Store the discs in a dry location where they are not
exposed to mechanical damage.
Protect cutting discs against shock, impact and harmful
environmental factors.
MAINS CONNECTION
Connect only to single-phase a.c. current and only to
the system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.

SPECIFIED CONDITIONS OF USE

The wall-chaser machine cuts slots for cables and pipes
(masonry grooves) in any kind of brickwork with two
diamond cutting discs running parallel to each other.
Do not use this product in any other way as stated for
normal use.
Appliances used at many different locations including wet
room and open air must be connected via a residual
current device (FI, RCD, PRCD) of 30mA or less.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs),
2006/42/EC, 2004/108/EC and the following harmonized
standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-22:2011 + A11:2013
EN 55014-1:2006 + A 1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
EN 50581:2012
Winnenden, 2014-09-10
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
6 ENGLISH
ADVICE FOR OPERATION
The machine switches off automatically if the motor is
overloaded. Allow it to cool, press the overload button and
restart the machine. If the overload protection switches it
off frequently, reduce the cutting pressure or depth of cut.
The infi nitely variable cutting width setting has the
advantage that, if the groove width is set correctly, pipes
etc. can be fi tted precisely into the groove and it is not
necessary to secure them with nails etc. to prevent them
from falling out.
Sharpen blunt diamond cutting blades (can be recognised
by sparks fl ying while cutting) by making several cuts into
calcareous sandstone or a special sharpening stone.
The cutting discs get very hot when in use. Do not touch
them before they have cooled down.
MAINTENANCE
The ventilation slots of the machine must be kept clear at
all times.
Use only Milwaukee accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the
six-digit No. on the label and order the drawing at your
local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the
machine.
Wear ear protectors!
Use an FFP2 particulate respirator as the
minimum amount of protection.
Wear gloves!
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool, tool in which protection against
electric shock does not rely on basic
insulation only, but in which additional safety
precautions, such as double insulation or
reinforced insulation, are provided.
There being no provision for protective
earthing or reliance upon installation
conditions.
European Conformity Mark
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
EurAsian Conformity Mark.
ENGLISH 7