Operating Elements And Connections; Safety Notes; Setting Into Operation - Monacor SIC-530 Mode D'emploi

GB Please unfold page 3. Then the described operat-
ing elements and connections can always be
seen.

1 Operating Elements and Connections

1 Soldering iron support
2 Slots to slide in the soldering iron support
3 LED temperature display
4 5-pole DIN jack to connect the soldering iron
5 Toggle switch to switch the soldering station on
and off
6 Rotary control to set the soldering temperature
7 Switch DISPLAY to switch over the temperature
display (3)
Position SET:
Position READ: Display shows the actual solder-
8 Heating display HEATER ON
9 State indication of the temperature display
If the switch DISPLAY (7) is in position SET, the left
field SET is lighting: The display shows the desired
soldering tip temperature.
If the switch DISPLAY is in position READ, the right
field READ is lighting: The display shows the ac-
tual soldering tip temperature.
10 Screw sleeve of the soldering iron
11 Soldering tip

2 Safety Notes

The appliance corresponds to the directive for electro-
magnetic compatibility 89/336/EEC and the low volt-
age directive 73/23/EEC.
This unit uses dangerous mains voltage (230 V~).
To prevent a shock hazard do not open the cabinet.
Leave servicing to authorized skilled personnel only.
Also any guarantee claim expires if the unit has
been opened.
For the operation also watch in any case the following
items:
•
The unit is only suitable for indoor use.
•
Avoid excessively warm locations for the unit or high
humidity (permissible operating temperature range
0-40°C).
•
Keep the unit away from children!
•
To avoid a fire or other damage by the hot soldering
iron, place the soldering iron in the support or on a
fire-proof base only.
•
The heated-up soldering iron must only be touched
at the handle. If metal parts of the soldering iron are
touched, there is the danger of burning. After finish-
ing the work, have the soldering iron only cool down
in the air, by no means chill it in water.
•
Do not take the unit into operation and immediately
take the mains plug out of the mains socket if:
1. damage at the unit or mains cable can be seen,
2. a defect might have occurred after a drop or simi-
lar accident,
6
Display shows the desired sol-
dering tip temperature set with
the rotary control.
ing tip temperature
3. there are malfunctions.
The unit must in any case be repaired by author-
ized skilled personnel.
•
A damaged mains cable must only be repaired by
the manufacturer or authorized skilled personnel.
•
Never pull the mains plug out of the mains socket by
means of the mains cable.
•
If the unit is used for purposes other than originally
intended, if it is operated in the wrong way or not
repaired by authorized skilled personnel, there is no
liability for possible damage.
•
For cleaning the housing do not use any sharp
detergents or chemicals. Do not immerse the unit
into liquid under any circumstances resp. do not let
liquid enter into the unit.
•
Important for U.K. Customers!
The wires in this mains lead are coloured in accord-
ance with the following code:
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured blue must be con-
nected to the terminal in the plug which is
marked with the letter N or coloured black.
2. The wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.

3 Setting into Operation

IMPORTANT! To avoid overheating damage, the sol-
dering station must not be operated without soldering
tip.
1) Connect the soldering iron with the soldering sta-
tion. For this plug the 5-pole angled DIN plug of the
soldering iron into the jack (4).
2) Slide the soldering iron support (1) into one of the
slots (2).
3) Connect the soldering station with the mains plug
to a mains socket (230 V~/50 Hz).
4) To switch on the station, press the toggle switch (5).
The digital LED temperature display (3) and the
heating display HEATER ON (8) light up.
5) Slide the switch DISPLAY (7) to position SET. The
left field SET of the state indication (9) lights up. Set
the temperature (170-480°C) with the rotary con-
trol (6). The desired temperature is shown by the
display (3).
6) Then slide the switch DISPLAY to the right to posi-
tion READ. The right field READ of the temperature
state display lights up. With this switch position the
display shows the actual heating-up temperature
resp. the temperature of the soldering tip. While
heating up, the display HEATER ON is lighting. It
expires as soon as the adjusted temperature will be
reached.