Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
− Place aluminium straightedge as
shown over outfeed table and cut-
terblock.
78
− Turn cutterblock by hand one turn
against the direction of feed.
− The planer knives are set correctly if
the straight edge is moved forward 4
to 6 mm by the turning cutterblock.
This check must be performed at
both ends of the cutterblock.
11. To set the knife projection, turn the
grub screws in the planer knife lock-
bar with a 3 mm Allen key as
required.
12. To tighten, turn the four hexagon
head screws of the planer knife lock-
bar fully out. To prevent distortion of
the planer knife lockbar start with
the screws in the centre, then
tighten the screws closer to the
edges.
A
Danger!
− Do not extend tool when tighten-
ing the screws.
− Do not tighten bolts by striking
the wrench.
13. Return cutterblock guard extrusion
to its starting position.
14. Mount jointer fence.
7.2
Feedgear Maintenance
1.
Unplug power cable.
2.
Unscrew the two cap nuts of the
drive cover and remove the drive
cover.
3.
Remove chips and dust with dust
collector or brush.
4.
Apply a light coat of care and main-
tenance spray to roller chain and
shaft and axle bearings (do not use
oil!).
5.
Replace drive cover and secure with
the two cap nuts.
7.3
Drive Belt Tensioning
1.
Unplug power cable.
2.
Unscrew cap nut of drive belt cover
and remove cover (80).
3.
Check belt tension with thumb pres-
sure. The drive belt (79) should not
give more than 10 mm in the centre.
If the drive belt requires tensioning:
4.
Loosen the four motor mounting
screws by approx. one turn.
79
81
5.
Push motor down to tension belt.
6.
When belt tension is correct tighten
motor mounting screws (81) cross-
wise.
7.
If necessary, remove chips and dust
with dust collector or brush.
8.
Put belt cover back on and secure
with cap nut.
7.4
Machine Care
1.
Unplug power cable.
2.
Remove chips and dust with dust
collector or brush from
− cutterblock;
− height-setting mechanism of cut-
terblock guard extrusion;
− thicknesser bed spindles;
− thicknesser feed drive.
3.
Apply a light coat of care and main-
tenance spray to the following com-
ponents (do not use oil!):
− thicknesser bed spindles;
− height-setting mechanism of cut-
terblock guard extrusion.
4.
Apply a light coat of anti-seize com-
pound to infeed table, outfeed table
and thicknesser bed.
7.5
Transporting the Machine
A
Caution!
To carry the machine two persons are
required.
Do not carry the machine holding it at
the infeed and outfeed tables, these
are not designed to bear the weight of
the machine.
1.
Remove jointer fence.
2.
Remove outfeed table.
3.
Lower cutterblock guard extrusion
fully and push extrusion all the way
in.
4.
Set thicknesser bed to about half the
thicknessing height.
5.
Put two roofing battens or 2 x 4's
through the machine and lift it with
the battens.
7.6
Machine Storage
A
Danger!
80
Store machine in such manner that
− it cannot be used or tampered
with by unauthorized persons,
and
− that nobody can get hurt while
the machine is turned off.
A
Caution!
Do not store machine unprotected
outdoors or in damp environment.
7.7
Maintenance
The checks and procedures described in
this section are an aid to safety! Should
there be faults evident on any of the
mentioned components, the machine
must not be used until these faults have
been remedied in a workmanlike man-
ner.
Prior to operation
Anti-kickback
lock
ENGLISH
Check:
− mobility of anti-
kickback fin-
gers (must fall
down by their
own weight)
− points of anti-
kickback fin-
gers
(not rounded)
23
Publicité
Chapitres
Table des Matières
