UNIPRODO UNI POOL REEL 520 Manuel D'utilisation page 5

EN
n) It is recommended to not use excessive force while
winding the pool cover. If blockages occur, they must
be removed first.
3. USE GUIDELINES
The product is designed for rolling, unrolling and storing
the solar film. The user is liable for any damage resulting
from nonintended use of the device.
3.1. DEVICE DESCRIPTION
ATTENTION! This product's view can be found on the
last pages of the operating instructions (pp. 31-36).
UNI_POOL_REEL_520 (See fig. I)
1. Movable support
2. Fixed support
3. Clamp screw
4. The base of the fixed support
5. The cap of the support
6. Base of the movable support
7. Wheels
8. Connector
9. Wheel for driving the roller
9.1. Handle
9.2. Mandrel
9.3. Plug
9.4. Safety beams
9.5. Washer
9.6. Screw
10. Roller axle
11. Roller axle
12. Handle
13. Bolt
14. Screw
15. Screw with nut
16. Long screw with a nut
17. Screw with a cap nut
18. Protective washer
19. Plug
20. Washer
21. Roller guiding the wheel
22. Strap with a female Velcro fastener
23. Male Velcro fastener
24. Clamp
25. Clip
UNI_POOL_REEL_570 (See fig. II)
1. Movable support
2. Fixed support
3. Roller axle
4. Roller axle
5. A wheel with a handle to drive the roller
6. Handle
7. Flat head bolt
8. Screw
9. Bolt with nut
10. Long bolt with a nut
11. Washer
12. Roll
13. Wheel
14. Belt with a female Velcro fastener
15. Male Velcro fastener
16. Clamp
17. Clip
UNI_POOL_REEL_585 (See fig. III)
A. Roller support
B. Roller support
C. Handle
D. Lever
8
E. A strap with a female Velcro fastener
F. Male Velcro fastener
G. Clamp
H. Clip
J. Support base (for mounting on a flat pool edge)
K. Base with handle (for mounting on a tubular frame)
L. Self-tapping bolt (long)
M. Self-tapping bolt (short)
N. Screw and nut
O. Flat head screw
P. Adapter for hexagonal tube
Q. Small hexagonal tube
R. Large hexagonal tube
3.2. ASSEMBLY OF THE DEVICE
UNI_POOL_REEL_520
1. (See fig. IV). Fix the axles of the roller with the screws
(13) to the outer tubes type A.
2. (See fig. V) Mounting the wheel to drive the roller (9):
a) Push both parts of the wheel together.
b) Insert the safety beams (9-4) between both parts
of the wheel (9).
c) Secure the connection with four bolts (9-6) and
washers (9-5).
d) Mount the handle (9-1). Insert the mandrel (9-2)
into the lever hole, then insert the holder with
the spindle into the hole of the wheel driving
the roller (9) and secure the connection with the
plugs (9-3).
3. (See fig. VI) Insert the fixed support base (4) and the
fixed support (2) into the clamping nuts and then into
the connector (8). Tighten the clamping nuts. Secure
the connections with screws and cap nuts (17), and
then insert the plugs (5) on both ends of the fixed
support base (4).
4. (See fig. VII) Insert the base of the movable support
(6) and the movable support (1 ) with clamping nuts
and connector (8). Tighten the clamping nuts. Secure
the connections with screws and cap nuts (17), and
then slightly tighten the clamp screw (3). Place the
wheels (7) on the axles of the movable support (6).
Then insert the guide roll (21) into the centre of the
wheels and secure the connection with the locking
washer (18) and the plug (19).
5. (See fig. VIII) Put the roller axle (11) through the
movable support (1) and install the wheel on it to
drive the roller (16). Secure the connection with the
screw and nut (16). Put the roller axle (10) through
the fixed support and mount the washer (20) and
the holder (12) on it. Secure the connection with the
screw and nut (15).
6. (See fig. IX) Position both supports no closer than 45
cm from the opposite sides of the pool. In the case
of a rectangular pool, the roller should be positioned
along the shorter edge. In the case of an oval shaped
pool, the roller should be positioned above the water
surface no more than 90 cm from the edge. Connect
the tubes of the roller so that their minimum overlap
is not less than 30 cm.
7. (See fig. X) Insert 3 screws (14) into the tube's
connections, with the force ensuring stable position
of the tubes in relation to each other.
8. (See fig. XI) Disconnect the male Velcro straps (23)
from the female Velcro straps (22), remove the
adhesive protection layer. Stick the male Velcro parts
(23) on the roller, perpendicular to its axle at regular
intervals, along the entire length of the pool. Velcro
straps should be placed no closer than 30 cm from
the edge of the pool (X in the figure indicates the pool
width).
9. (See fig. XII) Fit the clamp (25) and the clip (24) on the
strap.
10. (See fig. XIII) In the case of rectangular pools. Spread
the cover over the pool. Attach the clips (25) (as
shown in the figure) for the cover, keeping at equal
intervals a distance from the next clips (25) like the
male Velcro parts (23) on the roller. Ensure that the
length of the straps allows covering to lie flat on the
pool surface to prevent air from blowing under the
cover.
11. (See fig. XIV) For round or oval pools. Spread the cover
over the pool. Install the clips (25) (as shown in the
figure) for covering at regular intervals at a distance
like the male Velcro parts (23) on the roller. Ensure
that the length of the straps allows covering to lie flat
on the pool surface to prevent air from blowing under
the cover.
UNI_POOL_REEL_570
1. (See fig. XV) Screw the axles of the roller with the
screws (7) to the outer tubes type A.
2. (See fig. XVI) Place the wheels (13) on the axles of the
base beam (2), insert the roll (12) into the centre of
the wheels and secure the connection with a washer
and a plug.
3. (See fig. XVII) Insert the roll into the rod and then
fasten both parts in the wheel to drive the roller (5).
Secure the connection with the plug.
4. (See fig. XVIII) Put the roller axle (3) through the fixed
support (2) and install the wheel on it to drive the
roller (5). Secure the connection with the screw and
nut (10). In the upper part of the fixed support (2),
install the clamp screw. Put the roller axle (4) through
the hole in the movable support (1) and mount the
washer (11) and the holder (6) on it. Secure the
connection with the screw and nut (9).
5. (See fig. XIX) Position both supports no closer than 45
cm from the opposite sides of the pool. In the case
of a rectangular pool, the roller should be positioned
along the shorter edge. In the case of an oval shaped
pool, the roller should be positioned above the water
surface no more than 90 cm from the edge. Connect
the tubes of the roller so that their minimum overlap
is not less than 30 cm.
6. (See fig. XX) Disconnect the male Velcro straps (15)
from the female Velcro straps (14), remove the
adhesive protection layer. Stick the male Velcro parts
(15) on the roller, perpendicular to its axle at regular
intervals, along the entire length of the pool. Velcro
straps should be placed no closer than 30 cm from
the edge of the pool (X in the figure indicates the pool
width).
7. (See fig. XXI) Fit the clamp (16) and the clip (17) on the
strap.
8. (See fig. XXII) In the case of rectangular pools. Spread
the cover over the pool. Mount the clips (17) (as
shown in the figure) for covering at regular intervals at
a distance as the male Velcro parts (15) on the roller.
Ensure that the length of the straps allows covering to
lie flat on the pool surface to avoid blowing air under
the cover.
9. (See fig. XXIII) For round or oval pools. Spread the
cover over the pool. Mount the clips (17) (as shown
in the figure) for covering at regular intervals at a
distance as the male Velcro parts (15) on the roller.
Ensure that the length of the straps allows covering to
lie flat on the pool surface to avoid blowing air under
the cover.
9 EN
UNI_POOL_REEL_585
1. (See fig. XXIV) Insert the levers (D) into the support (A),
then slide the holder (C) into the support (B).
2. (See fig. XV) Screw the bolt (L) into the hole in the base
(A) and (B). It is recommended to use a screwdriver
with a magnetic tip that will hold the screw during
assembly.
3. (See fig. XXVI) The required roller length is marked as
the distance X from the inside of the support (A) to the
inside of the second support (B) when both supports
are positioned on opposite sides of the pool.
To measure the distance X for flat-edge pools:
a) Insert the bases (J) into the bottoms of the
supports (A) and (B).
b) Place the supports (A) and (B) on the edge.
c) Measure the distance between the inner sides of
the supports (A) and (B).
To measure the distance X for pools with banks in the
form of a tubular frame:
a) Insert the bases (K) into the bottoms of the
supports (A) and (B).
b) Place supports (A) and (B) on the tubular frame
and secure their position by tightening the screws
on the bases (K).
c) Measure the distance between the inner sides of
the supports (A) and (B).
4. (See fig. XXVII) Possible configuration of tube
connection. PLEASE NOTE: The minimum overlap
of pipes is 20 cm (8in). Openings in pipes (P and Q)
should be located at the outer ends of the connected
pipes to enable installation of both one support (A)
and the other support (B).
5. (See fig. XXVIII) To secure the connection of one pipe
(R) to another pipe (P or Q), screw the screws (O) into
the holes on the pipe (R). Keep the minimum overlap
of the tubes 20cm (8in).
6. (See fig. XXIX) After connecting the tubes, they should
be mounted on the support axles (A and B). It must be
ensured that the second opening on the pipe (P and
Q) and the hole in the support axis are in the same
position to allow the screw (M) to be installed. Secure
the connection with the screw (M).
7. (See fig. XXX) Position the roller supports (A and B)
together with the base (J) on the edge of the pool. In
case the edge is made of plastic or wood, use self-
tapping screws (L) to fix the base (J) to the edge. In the
case where the edge is made of metal, first drill holes
corresponding to the size of the opening in the base
(J). Secure the position of the support with the base
by screwing it to the edge with a screw and a nut (N).
If it is necessary to increase the length of the roller,
loosen the three screws (O) on the tube (R) at both
ends of the roller. Adjust the length of the roller and
tighten the screws (O) to secure the connection.
8. (See fig. XXXI) For pools with a tubular frame. Position
the roller supports (A and B) together with the base
and the holder (K) on the frame and tighten the
screws in the base with the holder (K) so that the
supports (A and B) are in a stable position. If it is
necessary to increase the length of the roller, loosen
the three screws (O) on the tube (R) at both ends of
the roller. Adjust the length of the roller and tighten
the screws (O) to secure the connection.
9. (See fig. XXXII) Connect the strap (E), the clamp (G) and
the clip (H).
10. (See fig. XXXIII) Disconnect the male Velcro parts (F)
from the strap (E) and remove the adhesive layer
from the male part of the Velcro. Place the male
Velcro parts (F) on the roller, perpendicular to its axle