Other Information; Connectivity Troubleshooting - Kimex 163-4320 Manuel D'utilisation

All found networks will be listed. Highlight your desired
network from the list and press OK to connect.
Note: If the modem supports N mode, you should set N
mode settings.
If the selected network is password-protected, enter the
correct key by using the virtual keyboard. You can use
this keyboard via the directional buttons and the OK
button on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established.
To disconnect from a wireless network, highlight
Network Type and press Left or Right buttons to set
as Disabled.
If your router has WPS, you can directly connect to the
modem/router without entering a password or adding
the network first. Highlight Press WPS on your wifi
router option and press OK. Go to your modem/router
device and press the WPS button on it to make the
connection. You will see a connection confirmation
on your Display once the devices have paired. Select
OK to proceed. No further configuration is required.
Highlight Internet Speed Test and press the OK button
to check your internet connection speed. Highlight
Advanced Settings and press the OK button to open
the advanced setting menu. Use directional and numeric
buttons to set. Highlight Save and press the OK button
to save settings when complete.

Other Information

You can also enable or disable Wake On feature using
the related option. The status of the connection will be
displayed as Connected or Not Connected and the
current IP address, if a connection is established.
Connecting to your mobile device via WLAN
• If available, you can download a virtual remote
controller application from the server of your mobile
device application provider.
Note: This feature may not be supported on all mobile devices.
Wake ON
Wake-on-LAN (WoL) and Wake-on-Wireless LAN
(WoWLAN) are standards that allow a device to be
turned on or woken up by a network message. The
message is sent to the device by a program executed
on a remote device connected to the same local area
network, such as a smartphone.
Your Display is WoL and WoWLAN compatible.
This feature might be disabled during the First Time
Installation process. To enable this feature set the
Wake On option in the Network menu as On. It
is necessary that both the device, from which the
network message will be sent to the Display, and the
Display are connected to the same network. Wake On
feature is only supported for Android OS devices and
can only be used via YouTube and Netflix applications.
In order to use this feature the Display and the
remote device should be connected at least once
while the Display is on. If the Display is powered off,
the connection should be re-established, the next
time it is switched on. Otherwise this feature will be
unavailable. This does not apply, when the Display is
switched into the standby mode.
If you want your Display to consume less power in
standby mode, you can disable this feature by setting
the Wake On option as Off.

Connectivity Troubleshooting

Wireless Network Not Available
• Ensure that any firewalls of your network allow the
Display wireless connection.
• Try searching for wireless networks again, using the
Network menu screen.
If the wireless network does not function properly,
try using the wired network. Refer to the Wired
Connectivity section for more information on the
process.
If the Display does not function using the wired
connection, check the modem (router). If the
router does not have a problem, check the internet
connection of your modem.
Connection is Slow
See the instruction book of your wireless modem to
get information on the internal service area, connection
speed, signal quality and other settings. You need to
have a high speed connection for your modem.
Distruption during playback or slow
reactions
You could try the following in such a case:
Keep at least three meters distance from microwave
ovens, mobile telephones, bluetooth devices or any
other WLAN compatible devices. Try changing the active
channel on the WLAN router.
Internet Connection Not Available
If the MAC address (a unique identifier number) of
your PC or modem has been permanently registered,
it is possible that your Display might not connect to
the internet. In such a case, the MAC address is
authenticated each time when you connect to the
internet. This is a precaution against unauthorized
access. Since your Display has its own MAC address,
your internet service provider cannot validate the MAC
address of your Display. For this reason, your Display
cannot connect to the internet. Contact your internet
service provider and request information on how to
connect a different device, such as your Display, to
the internet.
It is also possible that the connection may not be
available due to a firewall problem. If you think
English - 16 -