First Time Installation; Media Browser Menu; Media Playback Via Usb Input - Kimex 163-4320 Manuel D'utilisation

First Time Installation

When turned on for the first time, the language
selection screen will be displayed. Select the desired
language and press OK.
On the next screen, set your country preference and
press OK to continue.
You will be asked to set and confirm a PIN at this point.
For some country options, the PIN cannot be set to
0000, in this case you need to enter another 4-digit
number combination. You have to enter this PIN if you
are asked to enter a PIN for any menu operation later.
The Signage Settings menu will be displayed next.
Set ID, Auto Software Update options can be
configured using this menu. Model name, Serial
number and Software version options are for
information only. They will be grayed out and not
selectable. You can save the model information data
of the Display to a connected USB device using the
Save model information option. You can also copy
database files from a connected USB device to the
Display using the Clone from USB option. Refer to
the Signage Settings Menu Contents section for
more information on the options of this menu. After
the settings are completed, highlight Next and press
OK to continue.
On the next screen, the Network/Internet Settings
menu will be displayed. Please refer to Connectivity
section to configure a wired or a wireless connection.
If you want your Display to consume less power in
standby mode, you can disable the Wake On option
by setting it as Off. After the settings are completed
highlight Next and press OK button to continue.
The First Time Installation is completed.
To repeat this process and reset the Display's settings
to the factory defaults enter the Settings>Signage
menu, highlight First time installation and press
OK. A confirmation message will be displayed asking
whether you want to delete all settings and reset the
Display. Select Yes and press OK to confirm.
Note: Do not turn off the Display while initializing first time
installation. Note that, some options may not be available
depending on the country selection.

Media Playback via USB Input

You can connect 2.5" and 3.5" inch (HDD with
external power supply) external hard disk drives or
USB memory stick to your Display by using the USB
input/s of the Display.
IMPORTANT! Back up the files on your storage
devices before connecting them to the Display.
Manufacturer will not be responsible for any file
damage or data loss. Certain types of USB devices
(e.g. MP3 Players) or USB hard disk drives/memory
sticks may not be compatible with this Display. The
Display supports FAT32 and NTFS disk formatting.
Wait a little while before each plugging and unplugging
as the player may still be reading files. Failure to do
so may cause physical damage to the USB player
and the USB device itself. Do not pull out your drive
while playing a file.
You can use USB hubs with your Display's USB
input/s. External power supplied USB hubs are
recommended in such a case.
It is recommended to use the Display's USB input/s
directly, if you are going to connect a USB hard disk.
Note: When viewing image files the Media Browser menu
can only display 1000 image files stored on the connected
USB device.

Media Browser Menu

You can play back music and movie files and display
photo files stored on a USB storage device by
connecting it to your Display. Connect a USB storage
device to one of the USB inputs located on the rear
side of the Display.
After connecting a USB storage device to your Display
Media Browser menu will be displayed on the screen.
You can access the content of the connected USB
device any time later from the Sources menu. Select
the related USB input option from this menu and press
OK. Then select the file of your choice and press OK
to display or play it back.
You can set your Media Browser preferences by
using the Settings menu. Settings menu can be
accessed via the information bar which is displayed on
the bottom of the screen when pressed the Info button
while playing back a video file or displaying a picture
file. Press the Info button, highlight the gear wheel
symbol positioned on the right side of the information
bar and press OK. Picture Settings, Sound Settings,
Media Browser Settings and Options menus will be
available. The contents of these menus may change
according to the type of the currently open media file.
Only Sound Settings menu will be available while
playing back audio files.
Loop/Shuffle Mode Operation
Start playback and activate
Start playback and activate
Start playback and activate
Start playback and activate
,
To use the functions on the information bar highlight
the symbol of the function and press OK. To change
the status of a function highlight the symbol of the
English - 9 -
All files in the list will be contin-
uously played in original order
The same file will be played
continuously (repeat)
All files in the list will be played
once in random order
All files in the list will be con-
tinuously played in the same
random order.