Futurelight PHS-250 Mode D'emploi page 36

- Make a test of the function of each channel
1. Press [ENTER] for 3 seconds to enter main menu;
2. Select "tESt" by pressing [UP] button;
3. Press [ENTER], the display shows "tE-X", "X" stands for the channel no., value "1-F", such as if you
selected "tE-X", the projector will test the color channel, change the color one by one and show the rainbow
effect with different speed.
4. Press [ENTER] or [EXIT/DN] to exit.
- Editing program:
This menu item allows you to write a program into the memory (EEPROM) via the control panel or via
the external controller including "EDIT", "CONT", "RUN".
EDIT Procedure: (via Control Board only, edit and save the scene do not use controller )
1. Press [ENTER] for 3 seconds to enter main menu;
2. Select "EDIT" by pressing [UP] button;
3. Press [ENTER], the display shows "SCEX", "X" stands for the scene no. to be edited , value "1-F". Such
as "SCE1" means you will edit the scene 1;
4. Change the scene no. by pressing [UP],
5. Press [ENTER], the display shows "ParX", "X" stands for the channel no. Such as "Par1", it means you
are editing the channel 1 of the selected scene.
6. Select the channel no. you would like to edit by pressing [UP] BUTTON;
7. Press [ENTER] to enter editing for the selected channel , the fixture re-acts to your settings. The display
shows the DMX value for the editing channel relatively. Such as " 11XX", it stands for in the channel 1 of the
scene 1, the DMX value is XX , XX is a number value "01-FF";
8. Adjust the DMX value by pressing [UP], until you get the expect effect of this channel;
9. Press [ENTER] to enter the editing of the others channel of the scene;
10. Repeat steps 5-9, until you finish setting all the DMX values for all channels of this scene.
11. Once all the channels completed, the display will flash "tINE", "tINE" stands for the time needed to run
this scene;
12. Press [ENTER] to edit the time needed, the display shows "Nt-X", "N" stands for the scenes no., value
"1-F", "X" stands for the time needed to run in this scene, value "1-F". For example, "1t-2" means you need 2
th
seconds to run on scene 1, " 5t-F" means you need 15 seconds to run on the 5 scene;
13. Adjust the time needed by pressing [UP];
14. Press [ENTER] to save the settings for the scene you are editing, the display will change to the next
scene automatic ;
15. repeat step 3-14 to edit and other scenes, you can edit and save 15 (F) scenes maximum.
16. Press [EXIT/DN] to exit, now you have edit and saved 15 (maximum) scenes through the control board,
without use controller, and this type saved scenes can be saved by "CONT", and can be run when you enter
to "RUN"
EDIT Procedure (via external controller)
1. Press [ENTER] for 3 seconds to enter main menu;
2. Select "EDIT" by pressing [UP] button;
3. Press [ENTER], the display shows "SCEX", "X" stands for the scene no. to be edited , value "1-F". Such
as "SCE1" means the scene 1;
4. Change the scene no. by pressing [UP],
5. Press [ENTER], the display shows "ParX", "X" stands for the channel no. Such as " Par1", it means you
are editing the channel 1 of you selected scene;
6. Select the channel No. you would like to edit by pressing [UP] button;
7. Select "tINE" by pressing [UP]
8. Press [ENTER] to edit the time needed, the display shows "Nt-X", "N" stands for the scene no. value "1-
F", "X" stands for the time needed to run the scene, value "1-F".For example, "1t-2" means you need 2
th
seconds to run on scene 1, " 5t-F" means you need 15 seconds to run on the 5 scene;
9. Adjust the time needed by pressing [UP];
10. Press [ENTER] to exit;
11. Select "CNIN" by pressing [UP];
12. Press [ENTER], the display shows "ON" or "OFF";
13. Select "ON" if you want to edit the scene from a external controller, by pressing [UP];
14. Use the controller to edit the settings of each channel for this scene;
15. Press [ENTER] to save and turn to the editing for the next scene;
16. repeat step 4-15 to edit other scenes , you can edit and save 15 scenes maximum;
36