Rear Panel; Dimensions - JB Systems ME 2 Mode D'emploi

ENGLISH
11. Headphone jack: You can connect any modern stereo headphone to this 6.3mm
jack. Together with the cue selector (9) and the cue level (10) you can use it to
listen to the selected input channel.
12. Master volume: Controls the level of the master output. You can adapt this level
to your personal taste.
13. Input selector channel5: You can choose between the 2 line inputs connected
on the rear of the mixer. Both sources can be connected at the same time, just
select which one you want to select on channel 5.
14. Input selector channel4: You can choose between a phono, micro and line
input, connected on the rear of the mixer. When you connect a micro phone to the
"micro4" input, switch the selector to "mic4". The phono and line source can't be
connected at the same time! When you connect a turntable, put the selector to
"phono2". When you connect a source with line level output (like a CD-player),
switch the selector to "CD2".
Attention: The sound becomes very distorted when you connect a CD-player and
set the switch to "phono2", be careful!
15. Input selector channel3: You can choose between a phono, micro and line
input, connected on the rear of the mixer. When you connect a micro phone to the
"micro3" input, switch the selector to "mic3". The phono and line source can't be
connected at the same time! When you connect a turntable, put the selector to
"phono1". When you connect a source with line level output (like a CD-player),
switch the selector to "CD1".
Attention: The sound becomes very distorted when you connect a CD-player and
set the switch to "phono1", be careful!
16. Input selector channel2: You can choose between a micro or line input,
connected on the rear of the mixer. When you connect a micro phone to the
"micro2" input, switch the selector to "mic2". When you connect a source with line
level output (like a CD-player) to the "line1" input, switch the selector to "line1".
17. Input connector DJ Micro: The DJ micro can only be connected to the XLR
input on the front plate. This input is balanced but accepts any kind of microphone
equipped with an XLR connector. If your micro only has a jack connector, you can
use a special adapter such as the JB Systems "5-3381".
18. Talkover switch: Use this switch to mute the music channels (2 to 5) while you
are talking through the DJ microphone. You can choose to mute the music by
12dB or 18dB.
19. Channel faders: Used to set the level of each channel separately.
20. Crossfader: With this fader you can mix over between channels 3 and 4. The
crossfader only works when you move the faders (19) of both channels to the
desired level!

REAR PANEL

JB SYSTEMS
OPERATION MANUAL
3/20 ME2 MIXER
ENGLISH
Attention: For each input you must set the corresponding input selector on the
front panel in the correct position!
21. Input Micro2: Used to connect a micro with 6.3mm jack connector.
22. Input Line1: Used to connect any line level sound source.
23. Input Phono1/CD1: Used to connect a turntable or any line level sound source.
24. Input Phono2/CD2: Used to connect a turntable or any line level sound source.
25. Input Micro3: Used to connect a micro with 6.3mm jack connector.
26. Input Micro4: Used to connect a micro with 6.3mm jack connector.
27. Input Tuner on CH5: Used to connect any line level sound source.
28. Input Video on CH5: Used to connect any line level sound source.
29. Record output: Used to connect any recording equipment to the mixer. This
output is not influenced by the master volume (12)
30. Master output: Used to connect an amplifier. The output level can be set by the
master volume (12)
31. Mains fuse: main fuse to protect the mixer. Replace it only with the same type
and value: 20mm glass fuse 250V 500mA slow blow.
32. Mains cable: connect this cable to a 230V/50Hz mains outlet. Before use, inspect
the cable to be sure it's not damaged!
33. Earth connector: When a connected turntable produces humming noises, even
when it's not in use, you can try to connect its grounding wire to this connector.
This helps in many cases, unfortunately not always...
SPECIFICATIONS
Power Supply: AC 230 V, 50Hz
Fuse: 20mm glass fuse 250V 500mA slow
Frequency response: 20-20.000Hz (+/-2dB)
THD + noise: <0.1% @ 1kHz, 0dB
S/N Ratio (IHF-A): >50dB @ 1kHz.
Micro inputs: 1.5mV @ 10kΩ
Line/CD inputs: 150mV @ 22kΩ
Phono inputs: 3mV @ 47kΩ
Record output: 775mV @ 600Ω
Micro input: 775mV @ 600Ω
Talkover: -12dB, -18dB
Tone controls: +/-12dB @ 10kHz / 1kHz / 100Hz
Headphone: >8Ω 250mV
digital – max. 200mS
Echo effect:

Dimensions:

270(W) x 180(H) x 45(D) mm
Weight: 2Kg
JB SYSTEMS
OPERATION MANUAL
4/20 ME2 MIXER