Publicité
• Symbols affixed to your tools may not be
removed or covered. Information on the device
that is no longer legible must be replaced imme-
diately.
Before putting the unit into operation, read
and observe the instructions for use.
Your unit at a glance
► P. 3, item 1
1. EZGrip swivel coupling
2. LCD Display
3. Dial position indicator
4. Manual on/off button
5. Battery tray
6. Dial
7. [L/R] Button
8. [+]/[−] Button
9. Sensor connection
10. Inlet
11. Outlet
12. Flap
Scope of delivery
• Operating manual
• Irrigation computer
• Connector for garden hose
Using for the first time
Insert the battery
– Pull out the battery compartment on the back of
the unit.
– Insert the batteries. Pay attention to correct
polarity.
– Replace the battery compartment. Make sure
the gasket is in the correct position.
Connection
Note: We recommend programming the
unit before you connect it to a water tap.
– Turn off the water tap.
– Screw the coupling nut (10) manually onto the
water tap. Do not use tools.
– Turn on the water tap.
Programming
– Rotate the dial to positions indicated for setup.
– Press [L/R] button to switch between left and
right outlet for all programming
• Left and right outlets can function at the same
time (Water flow will decrease when both sides
are used at once.)
Note: The dial should be in the [ON] posi-
tion for the Timer to operate (programmed
mode or Manual mode)
Setting the clock
– Turn the dial to the [ ] position.
Handy Hints
• The LCD screen shows the countdown time until
the next watering. If you turn the dial from [ON] to
All manuals and user guides at all-guides.com
– The clock functions in 24hr mode. Press [+] but-
ton or [−] button to select the correct time (If you
press and hold the [+] or [−] buttons, the num-
bers will change more rapidly.)
Note: When the new batteries are inserted,
the default clock time is 12:00 PM.
Setting the start time
– Turn the dial to [
– Press [+] or [−] button to select the desired time
to start (If you press and hold the [+] or [−] but-
tons, the numbers will change more rapidly.)
• The default start time is 5:00AM.
Setting the watering duration
– Turn the dial to [ ].
– Press [+] or buttons, to select the desired water-
ing time (If you press and hold the [+] or [−] but-
tons, the numbers will change more rapidly.)
• The watering period can be set in minutes, any-
where between 1 and 360 minutes. (The default
watering period is 15 minutes.)
• If the [ ] is set to 0, the device will not operate.
Setting the watering frequency
– Turn the dial to [
– Press [+] or [−] buttons to select the desired fre-
quency.
– The watering frequency range is between 1 hour
to 7 days. The default watering frequency is 12
hours.
Watering Frequency Chart
1 HRS, 2 HRS, 4 HRS, 12 HRS, 1 DAYS, 2 DAYS,
3 DAYS, 4 DAYS, 5 DAYS, 6 DAYS, 7 DAYS
Note: the timer will not run when the [ ] you
set is greater than [
– Once you have set all of the above, turn the dial
to [ON]. The timer will run as per your set times.
Setting a rain delay (Set up when raining to
temporarily delay watering)
– Turn the dial to [ON].
– Press [+] button once to see the words [DELAY].
– Press [+] button again to select the number of
days you would like to delay watering. (eg. 24,
48, 72 Hrs)
• If no additional settings are made in 5 seconds,
the timer will save the current setting and exit to
the home screen (clock)
• The screen will then flash between the clock and
the rain delay time (in hours).
– Turn the dial to [OFF] or [ON], or set the rain
delay time to [0],if you would like turn off the rain
delay function.
Rain Delay Time Chart
0 HRS, 24 HRS, 48 HRS, 72 HRS
– [ ]: Press this button to activate manual watering
mode.
any other position, the watering will stop immedi-
ately.
GB
].
].
].
17
Publicité
