Toto CST412MF Manuel D'installation Et D'utilisation page 4

7) Install the side screws to the mounting blocks. Cover the screw head with the provided screw-cap (see Ill. 6).
If the side screw does not engage the mounting blocks, then either the toilet bowl is not
fully inserted in the socket or the mounting block is not installed properly.
not installed properly, it may slide out of socket during use or cause leaks. Please ensure that
CAUTION
both sides are properly fitted and secure. Do not over-tighten the screws, as it may result in
product damage.
8) Connect the water supply hose to the fill valve.
tighten, then using wrench, do not exceed 1/4 turn.
BEFORE the tank-to-bowl installation. TOTO recommends using a flexible supply hose.
Please be sure to connect the water supply hose to the fill valve before installing the tank to the bowl. If
procedure is reversed, the water supply installation may be impossible.
CAUTION
FAILURE TO FOLLOW THIS INSTRUCTION MAY RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE.
9) Install the tank-to-bowl gasket over the flush valve outlet on underside of the
tank (see Ill. 7).
Pick up the tank and carefully guide the flush valve hose into the bowl inlet
hole on the bowl tank-shelf. Make sure the bolts on the bowl fit through the
opening in the base of the tank.
10) For easy assembly, remove the top-portion of the flush valve by disconnecting
the refill tube. Turn the upper portion of the flush valve counter-clockwise, and
pull it up (see Ill. 8). Insert the rubber washer then metal washer on the mount-
ing bolt. Thread on the nuts, hand-tighten before releasing the tank. Tighten
the nuts evenly until tank sets snugly on each of the three contact points on
the bowl. Re-install flush valve and refill tube.
Do not over-tighten the mounting bolt. Over tightening may
result in product breakage and cause personal injury and/or
CAUTION
property damage.
11) Carefully place the lid on top of the tank, making sure that the push rod colors
match the flush valve buttons (blue to blue and white to white).
If the button(s) is too low (see Ill. 9):
1) Loosen the lock nut/s counterclockwise.
2) Turn the rod(s) counterclockwise to lengthen
(each full turn is 1mm).
3) Place the lid on the tank to check the buttons.
If rod(s) is too long, water will keep running in the toilet.
1) Loosen the lock nut(s) counterclockwise.
2) Turn the rod(s) clockwise to shorten them.
Adjust the rods as necessary by turning the rod 1 full turn
(see Ill. 10); to lengthen, turn the rod counterclockwise; to
shorten, turn the rod clockwise. When the adjustment is
completed, tighten the lock nut to secure it.
12) Connect the opposite end of the water supply tube to the
angle stop (see Ill. 11). Open the supply valve and flush the
toilet several times. Check all the connections for leaks and
periodically afterwards following the installation.
13) The toilet seat is installed with the top-mount bolt set (see Ill. 12). Insert the
rubber bushing-nut into the seat mounting holes. Place the seat on the bowl
and rotate the hinge unit into place while holding the seat down on the bowl.
Tighten the bolt from the top with the screwdriver.
WARNING! DO NOT USE IN-TANK BOWL CLEANERS
The use of high concentration of chorine or chlorine base products can damage
the fittings in the tank. Damage to the tank fittings may cause leakage and/or
property damage. TOTO shall not be responsible or liable for any tank fitting
failure or damage caused by the use of in-tank bowl cleaners.
Installation Procedure (continued)
Do not overtighten water supply hose to fill valve. First hand-
The water supply hose must be connected to the fill valve
Tank Lid
Ill. 9
Tank
The rod(s) is too short, the buttons are lowered.
4
If the toilet is
Ill. 8
Push
Buttons
Left Right
Partial Full
Flush Flush
Push Button
Assembly
Ill. 10
Lid
Flush Valve
Lock Nut
Buttons are at the correct level.
Ill. 11 Ill. 12
Ill. 6
Ill. 7
Gasket
Push Button
Housing
Adjustable
Push Rods
Tank
Lid
Mounting
Nut
Clip
Clockwise/
Counterclock-
wise
Seat Bolt
Rubber Brushing Net