Assembling The Components; Setting The Cutting Height; Starting Up - Einhell Royal RBM 51 Instructions De Montage Et Mode D'emploi

Anleitung_RBM_51_SPK1:_

4. Assembling the components

Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A flat oil drip tray (for changing the oil)
A 1 liter measuring jug (oil/petrol resistant)
A petrol can (5 liters is sufficient for approx. 6
operating hours)
A funnel (suitable for the tankʼs petrol filler neck)
Household wipes (to wipe up oil/petrol residue;
dispose of these at a filling station)
A petrol suction pump (plastic, available from
DIY stores)
An oil can with hand pump (available from DIY
stores)
1 liter of engine oil (10W30)
Assembly
1. Take the mower and attachment parts out of the
packaging and check that all parts are present
(Fig. 2).
2. Fasten the push bar using a square head screw
(Fig. 3a/Item 15), a washer (Fig. 3a/Item 17) and
a star nut (Fig. 3a/Item 18) on each side. For
fastening choose one of the three holes to suit
the required height of the handle. Important! The
identical height must be set on both sides.
Ensure that the cords which are fastened later
are not in the way.
3. Fasten the top push bar to the bottom push bar
using a screw (Fig. 3b/Item 16), a washer (Fig.
3b/Item 17) and a star nut (Fig. 3b/Item 18) on
each side.
4. Insert the grip of the starter cord (Fig. 3c/Item 4)
into the hook provided for that purpose (Fig.
3c/Item 24) as shown in Figure 3c.
5. Fasten the cords to the push bar with the
supplied cable ties (Fig. 3d/Item. 13).
6. Lift the ejector flap (Fig. 4 / Item 8) with one hand
and hook in the grass bag (Fig. 4/Item 7) as
shown in Figure 4
05.09.2007 14:23 Uhr Seite 21

5. Setting the cutting height

Important! Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
Before you begin to mow, check to ensure that
the blade is not blunt and that none of the
fasteners are damaged. To prevent any
imbalance, replace blunt and/or damaged blades
as a set only (if applicable). To carry out this
check, first switch off the engine and pull the
spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever
(Fig. 8/Item 9). Up to 5 different cutting heights
can be selected.
Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position.

6. Starting up

Important!
The engine does not come with oil in it.
Therefore, ensure that you add 0.6 liters of oil
before starting it up. Use normal, multigrade oil
(10W30). The oil level in the engine must be
checked each time before mowing. (see
Checking the oil level).
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig. 5a/Item A) which must be pulled back
before the engine can be started. When the engine
control lever is released it must return to its initial
position, at which point the engine automatically
switches off.
Before you start the lawn mower, open the petrol
cock (Fig. 6, arrow = petrol cock open). Move the
speed lever (Fig. 7) to position "N". Press the
engine brake lever (Fig. 5b) together and give the
starter cord a vigorous pull. You can control the
rotation speed of the blade using the speed lever
(Fig. 7).
Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
Whenever you need to perform any kind of adjust-
ment and/or repair work on your lawn mower, wait
until the blade has come to a complete stop.
GB
21