Device List - Connect To The Paired Device; Restart Bluetooth Pairing; Aux In Mode; Setting The Clock - PERFECTPRO ROCKBOX 2 Manuel De L'utilisateur

Device List – Connect to the paired device
In the radio, you can select the Bluetooth device from the Device list to connect again.
The device names would be shown if the name of the Bluetooth devices were configured
in the mobile devices. Please refer to the user manual of your mobile device for the
configurations.
The Device list can be checked as below:
1. In Bluetooth mode, press the Menu button to enter the system setting.
2. Rotate the Tuning knob until "Device list" is displayed; press the TUNING knob to
select the setting.
3. Rotate the Tuning knob to view the name of the devices.
4. Press the Tuning knob to start Bluetooth reconnection. The speaker will
automatically connect to this selected mobile device.
Note: There can be up to 8 device names stored in the Device list memory. If you store
more than 8 mobile devices into the Device list memory, the earliest paired device name
will be erased.
Note: If you have ever deleted the "PP RockBox 2" from your connected mobile phone
device, the auto reconnection will be unsuccessful.

Restart Bluetooth pairing

The Bluetooth function can be set to operate in different ways as below:
1. In Bluetooth mode, press the Menu button to enter the system setting.
2. Rotate the Tuning knob to select the "Disconnect BT" option, and press the
Tuning knob to select the setting.
3. The LCD display will show "Please wait" for a few seconds in order to disconnect
the current connection with the mobile phone device.
4. The LCD display will show "Not connected" and the radio's Bluetooth is free for any
mobile phone device connection as it is in discoverable mode now.
Note: "Disconnect BT" is the option that forces the Bluetooth of this radio to disconnect
from your mobile phone and enter the "discoverable mode". This is the way to allow
the Bluetooth pairing to another device. If no new device is paired, the Bluetooth will
automatically try to connect to the last device when it is switched off and on again.
The Auto-Power management function will be activated in Bluetooth mode. If there is no
signal* for a period of over 15 minutes, the radio will automatically
switch to standby mode. Pressing the On/Off button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level on the external device enough to be detected.
13

AUX IN MODE

A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (not included with
this radio).
1. Connect an audio source to the Aux In socket.
2. Press the Source button to select AUX input. Display will show "AUX IN".
3. Play the external player.
4. Adjust the volume of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the AUX-IN socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal from the AUX input jack for a period over 15 minutes, the unit will automatically
switch to standby mode. The operation indicator and the LCD will go off in such case.
Pressing the On/Standby button will wake up the unit.

SETTING THE CLOCK

The clock can only be set when the radio is in standby mode. If no buttons are pressed
for 5 seconds, the radio will exit the clock setup and the setting is cancelled.
1. Press and hold the Time Set knob for 12 seconds until the hour digits flash on the display.
2. Rotate the Time Set knob to set the hour.
3. Press the Time Set knob to confirm, the minute digits flash.
4. Rotate the Time Set knob to set the minute.
5. Press the Time Set knob to confirm, the day flashes on the display.
6. Rotate the Time Set knob to set the current day.
7. Press the Time Set knob to confirm, the month flashes.
8. Rotate the Time Set knob to set the current month.
9. Press the Time Set knob to confirm, the year will then flash on the display.
10. Rotate the Time Set knob to set the current year.
11. Press the Time Set knob to confirm, "SYNCLOCK ON" flashes.
12. Rotary the Time Set knob to select "SYNCLOCK ON" or "SYNCLOCK OFF".
13. Press the Time Set knob to confirm and finish the clock setting.
RDS time synchronisation
If "SYNCLOCK ON" is selected, the symbol "
Some RDS stations transmit a time signal. If reception is good and you have
selected the "SYNCLOCK ON" option during the time setting, the time will be
automatically updated (" " flashes on the display). Time synchronisation can take
several minutes. The automatic time setting is always activated when the radio is
switched from standby to FM broadcasting and receives a RDS station.
GB
" will show on the clock display.
14