Using The Bluebull For The First Time; Using Bluetooth; Pairing Bluetooth With Your Mobile Device; Playing Music From Your Mobile Device - PERFECTPRO BLUEBULL Mode D'emploi

USING THE BLUEBULL FOR THE FIRST TIME

1. Place the Bluebull speaker on a flat surface.
2. Plug the AC power plug into the AC mains power socket.
Shortly push (for 1 second) the POWER button and the Battery Level LED's will
start flashing according to the battery charging process. Once the battery is full,
all 5 Battery Level LEDs will be lit constantly, then go completely off after about 9
seconds.
Should the battery be full or nearly full, then the Bluebull speaker will not start
charging and no Battery Level LEDs will animate at the push of the Power button.
3. Press and hold the POWER button for about 2 seconds and the Bluebull speaker
will start up to Bluetooth mode (the blue Pair LED will light up and start blinking).
NOTE: After connecting the Bluebull speaker to AC mains power the charging process
will not automatically be shown. The Battery Level LEDs will not light up automatically.
To check the battery charging process it is needed to shortly push (for 1 second) the
POWER button. The battery charging process will then be shown constantly by the
Battery Level LEDs until the battery is full. Shortly after the battery charging process has
reached the "full battery charge" level (all 5 Battery Level LEDs lit constantly) the Battery
Level LEDs will go off.
NOTE ON FIRST USE: BEFORE OPERATING THE BLUEBULL SPEAKER FOR THE
FIRST TIME ALWAYS FIRST FULLY CHARGE THE BATTERY.

USING BLUETOOTH

Pairing Bluetooth with your mobile device

It is necessary to first pair your Bluetooth device (e.g. phone or tablet) with your Bluebull
speaker before you can play/stream Bluetooth music through your Bluebull. Paring
creates a `bond' so the two devices can recognize each other and interact.
1. Press and hold the POWER button for about 2 seconds to turn on the Bluebull
speaker.
The Bluetooth connected LED on the front will be blinking when the Bluebull
2.
speaker is not yet paired with your mobile device.
3. On your mobile device open the Setting menu and select Bluetooth, then select
"BlueBull" in the Bluetooth devices list (Bluetooth pairing instructions may vary per
type of mobile device, please check your mobile device manual).
4. When Bluetooth pairing is successful, the Bluetooth connected LED will stop
blinking and be lit constantly.
NOTE: If your mobile device cannot be connected to the Bluebull speaker by Bluetooth,
please delete "BlueBull" from your mobile device's list and pair to the Bluebull speaker
again. For how to remove the existing Bluebull speaker called "BlueBull" from your
mobile device, please read the user manual of your mobile device for further assistance.
7
NOTES:
1) Bluetooth connectivity performance will very much also depend on the connected
Bluetooth source devices. Please refer to the Bluetooth capabilities of your device
before connecting to your Bluebull speaker. All features may not be supported on
some paired Bluetooth source devices.
2) The effective operation range between the Bluebull speaker and the paired device
is approximately 10 meters (30 feet). Any obstacle between the system and the
device can reduce the operational range. Some mobile devices may have a shorter
Bluetooth connection/transmission range.
3) Not all player applications or devices may respond to the navigation control buttons.
4) With some mobile devices, making/receiving calls, text messages, e-mails or
any other activities unrelated to audio streaming may mute the Bluetooth audio
streaming or even temporarily disconnect from your device. Such behavior is a
function of the connected device and does not indicate a fault in your Bluebull
speaker.

Playing music from your mobile device

1. Press and hold the POWER button for about 2 seconds to turn on the Bluebull
speaker.
2. The default mode is Bluetooth.
3. Start playing music by using the media players in the paired mobile device.
4. Playback can be controlled from the mobile device or by pressing the
FFW , and PLAY buttons on the Bluebull speaker.

Auto Bluetooth reconnection

When the Bluebull speaker has been switched off and then on again, it will automatically
try to reconnect to the last connected mobile device.
1. Press and hold the POWER button for about 2 seconds to turn on the Bluebull
speaker.
2. The default mode is Bluetooth.
3. The Bluebull speaker will try to connect to the last connected device and the
Bluetooth connected LED will be blinking.
4. If the Bluebull speaker can connect to the last mobile device used successfully, the
Bluetooth connected LED will be stop blinking and stay lit constantly.
NOTE: If you have deleted the "BlueBull" from your connected mobile device, the auto
reconnection will be unsuccessful.
GB
G B
REW,
8