Publicité
SYMBOLOGY
SPECIFICATIONS
Cat. No. ..................................................... 3632-20
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
Laser............................................................Class 2
Max Power........................................... P
Frequency....................................................10 KHz
Pulse Duration Normal Mode ................. T
Pulse Duration Power Save.................... T
Wavelength.......................................... 510-530 nm
Beam Divergence ........................................... 3 rad
Storage Temp .................................... -4°F to 120°F
Working Range .................................................125'
Range with Detector .........................................165'
Accuracy ...............................................±1/8" @ 33'
Settle Time ......................................... < 3 Seconds
Tripod Mount ..................................1/4"-20, 5/8"-11
Ingress Protection............................................ IP54
Drop Rating .......................................................1 m
Leveling ............Auto ±°4 side to side, front to back
Recommended Ambient
Operating Temperature .................... 0°F to 125°F
Volts
Direct Current
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Magnets
Read operator's manual
AVG
p
p
FUNCTIONAL DESCRIPTION
1
1
7
6
5
≤ 8 mW
10
≤ 80 µs
9
≤ 50 µs
LASER
Brookfield, WI 53005 USA
CAT. NO. 3632-20
SER.
WARNING
WARNING
To reduce the risk of injury, user
must read operator's manual. Use M12 batteries.
Pour minimiser les risques de
AVERTISSEMENT
AVERTISSEMENT
blessures, l'utilisateur doit lire
le manual. Utiliser des piles M12 .
™
Para reducir
ADVERTENCIA
ADVERTENCIA
el riesgo de
lesiones, el usuario debe leer el manual.
Utilice baterías de M12 .
™
Made in China
IEC 60825-1:2014-05 t
CONFORMANCE WITH IEC 60825-1 ED. 3., AS DESCRIBED IN LASER NOTICE NO. 56, DATED MAY 8, 2019. THIS DEVICE COMPLIES WITH PART 15
OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
1. Laser apertures
2. On/Off dial
3. Pivot Bracket
4. Micro adjust
5. Fuel gauge
WARNING
cific charging instructions, read the operator's
manual supplied with the charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
may be hazardous.
Use power save mode to extend the battery run
time. Power save mode is indicated by dimmed laser
beams and the Mode indicator pulsing. Visual range
is decreased in power save mode. To turn power save
mode ON or OFF, press and hold Mode button for 3
seconds. The tool will automatically switch to power
save mode if less than 7% of battery charge remains.
5
1
4
360°
3-PLANE
Milwaukee Tool
12 V
™
≤ 80 μs MAX OUTPUT P
≤ 8mW @ 510nm - 530nm
COMPLIES WITH 21 CFR 1040.10 AND 1040.11 EXCEPT FOR
P
AVG
6. Plane selector buttons
7. Power on indicator
8. Threaded inserts
9. Magnets
10. Nail/Screw hole
ASSEMBLY
Recharge only with the charger
specified for the battery. For spe-
Always remove the battery pack
any time the tool is not in use.
Only use accessories specifically
recommended for this tool. Others
Power Save
2
3
8
Publicité
