Kit Contains:
(1)
Mulcher Plate
(2)
Mulcher Blade
(2)
Latch Hooks
(2)
Screws
5(3/$&( 02:(5 %/$'(6 6HH )LJ
•
Raise mower to highest position to allow access to
blades.
•
Remove blade bolt securing blades.
•
Install mulcher blades with trailing edge up towards
deck as shown.
,03257$17 TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.
7KUHH EROW PDQGUHOV
•
Reassemble blade bolt, lock washer and fl at washer,
previously removed, in exact order as shown.
•
Tighten bolt securely (30-35 Ft. Lbs. torque).
)RXU EROW PDQGUHOV
•
Reassemble blade bolt.
•
Tighten bolt securely (45-55 Ft. Lbs. torque).
,03257$17: SPECIAL BLADE BOLT IS HEAT TREATED.
7+5(( %2/7 0$1'5(/
75$,/,1*
('*( 83
)/$7 :$6+(5
/2&. :$6+(5
)285 %2/7 0$1'5(/
75$,/,1*
('*( 83
67$5
21548523
,1&+ &87 02:(5 08/&+(5 .,7
0RGHO 1XPHU 0.%
,167$//$7,21 ,16758&7,216
(2)
Lock Washers
(2)
Flat Washers
(2)
Weld Nuts
0$1'5(/
$66(0%/<
67$5
%/$'(
%/$'( %2/7
63(&,$/
0$1'5(/
$66(0%/<
%/$'(
%/$'( %2/7
63(&,$/
),*
,167$// 08/&+(5 3/$7(
6HH )LJV
•
Install two latch hooks to mulcher plate using screw,
washer, lock washer, and weld nut as shown.
127(: Pre-assemble weld nut to latch hook by inserting
weld nut from the top with hook pointing down.
•
Tighten hardware securely.
:(/' 187
)520 7+( 723
:(/'
187
/2&.
:$6+(5
6&5(:
/$7&+
+22.
:$6+(5
02964
08/&+(5
3/$7(
),*
&$87,21'R QRW UHPR YH GLVFKDUJH JXDUG
IURP PRZHU 5DLVH DQG KROG JXDUG ZKHQ
DWWDFKLQJ PXOFKHU SODWH DQG DOOR Z LW WR
UHVW RQ SODWH ZKLOH LQ RSHUDWLRQ
•
Raise and hold defl ector shield in upright position.
•
Place front of mulcher plate over front of mower deck
open ing and slide into place.
127( On mowers so equipped, place slot in mulcher
plate over tab on mower and position plate over mower
opening as shown.
•
Hook front latch hook into hole on front of mower
deck.
•
Hook rear latch hook into hole on back of mower
deck.
:,7+287
*$8*(
:+((/6
+22. 32,176
'2:1
/$7&+
+22.
:(/'
/2&.
187
:$6+(5
:$6+(5
6&5(:
'()/(&725
6+,(/'
7$%
,) (48,33('
/$7&+
+22.6
),*
199974 08.15.05 Printed in U.S.A.