Publicité
Liens rapides
Installation guide
Colibri® Electric Expansion Valves
Type ETS 12C, ETS 24C, ETS 25C, ETS 50C, ETS 100C
English
Refrigerants : R410A, R404A, R507, R134a, R407A, R407B, R407C, R407F, R32, R290, R1234ze, R1234yf, R449A,
R449B, R452A, R1270, R600, R600a, R22, R23, R227, R417A, R444B, R447A, R448A, R454B, R422A, R422D, R427A,
R502, R513A, R413A, R438A, R450A, R455B, R454C, R454A, R452B and *L40
*R-number allocation by ASHRAE is pending
Allowable ambient temperature:
Min. -40 °C / -40 °F
Max. 70 °C / 158 °F
Stepper motor type:
Bipolar
Do not connect directly to AC/DC power source.
Connect valve to appropriate controller/driver only.
ETS Colibri® valves are delivered in open position, ready for brazing.
An AST –g service driver is available for manual operation / service of ETS C valve.
Flow direction
MADE IN DENMARK
Colibri® Electric
Expansion valve
ETS XXXC
N0311A
10 , 800mA peak
PS 50bar / MWP 735psig
-40/+70°C / -40/+158°F
034GXXXX
Bi-flow
Reverse flow
Application
Place the valve close to the evaporator.
It is recommended to use Danfoss filter drier before the expansion valve or
a strainer for particles of 150 micron or smaller.
© Danfoss | DCS (sw) | 2017.01
Fluid temperature:
Min. -40 °C / -40 °F
Max. 70 °C / 158 °F
Phase current:
800 mA peak /
600 mA RMS
Reverse
Normal
Normal flow
(Using sight glass for flash gas detection - ETS 25C to ETS 100C)
ETS Colibri®
ENGINEERING
T O M O R R O W
Max. working pressure:
50 bar / 725 psig
Coil resistance:
10 Ω (20 °C / 68 °F)
GREEN:
YELLOW: WET
MADE IN DENMARK
Colibri® Electric
Expansion valve
ETS XXXC
N0311A
Reverse
10 , 800mA peak
PS 50bar / MWP 735psig
-40/+70°C / -40/+158°F
034GXXXX
Total steps:
600 full steps
DRY
Normal
Danfoss
Danfoss
R64-3002.1
R64-3002.11
DKRCC.PI.VD1.F4.ML | 1
Publicité
Manuels Connexes pour Danfoss Colibri ETS 12C
Sommaire des Matières pour Danfoss Colibri ETS 12C
- Page 1 R64-3002.1 ETS Colibri® Place the valve close to the evaporator. It is recommended to use Danfoss filter drier before the expansion valve or a strainer for particles of 150 micron or smaller. DKRCC.PI.VD1.F4.ML | 1 © Danfoss | DCS (sw) | 2017.01...
- Page 2 Motor coil resistance check. N0311A 10 , 800mA peak PS 50bar / MWP 735psig -40/+70°C / -40/+158°F 034GXXXX Coil A = Coil B = 10 Ω (20 °C / 68 °F) Installation video DKRCC.PI.VD1.F4.ML | 2 © Danfoss | DCS (sw) | 2017.01...
- Page 3 Es wird empfohlen, Filtertrockner von Danfoss vor dem Expansionsventil oder einem Filter für Partikel von 150 µm oder kleiner ist. Il est recommandé d’utiliser un filtre déshydrateur Danfoss avant la vanne de détente, ou un filtre à particules de 150 microns ou moins.
- Page 4 Bobine A = Bobine B = 10 Ω (20 °C) MADE IN DENMARK Colibri® Electric Expansion valve ETS XXXC N0311A 10 , 800mA peak PS 50bar / MWP 735psig -40/+70°C / -40/+158°F 034GXXXX Installation Video Installation vidéo DKRCC.PI.VD1.F4.ML | 4 © Danfoss | DCS (sw) | 2017.01...
- Page 5 R64-3002.1 ETS Colibri® Colocar la válvula próxima al evaporador. 阀关闭位置， 靠近蒸发器侧 Se recomienda utilizar un filtro deshidratador Danfoss antes de la válvula de expansión o un filtro para partículas de 150 micras o menores. 建议在膨胀阀前使用丹佛斯干燥过滤器或使用过滤目数小于等于150微米的过滤网 DKRCC.PI.VD1.F4.ML | 5 © Danfoss | DCS (sw) | 2017.01...
- Page 6 MADE IN DENMARK Colibri® Electric 电机线圈电阻检查 Expansion valve ETS XXXC N0311A 10 , 800mA peak 在20℃时， 线圈A=线圈B=10Ω PS 50bar / MWP 735psig -40/+70°C / -40/+158°F 034GXXXX Instalación vídeo 安裝 視頻 DKRCC.PI.VD1.F4.ML | 6 © Danfoss | DCS (sw) | 2017.01...