Bosch Professional GKP 200 CE Notice Originale page 8

8 | English
Do not touch the nozzle while it is hot. There is a risk of
u
burns.
Product Description and
Specifications
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The glue gun is intended for solvent-free gluing of materials
such as paper, cardboard, cork, wood, leather, textiles,
foam materials, plastic (except PE, PP, PTFE, Styrofoam®
and plasticised PVC), ceramics, porcelain, metal, glass and
stone.
Product Features
The numbering of the product features refers to the illustra-
tion of the glue gun on the graphics page.
(1) Heat shield
(2) Nozzle
(3) Support bracket
(4) Feed trigger
a)
(5) Charging station
(6) Mains cable
(7) Power indicator
a)
(8) Glue stick
a) This accessory is not part of the standard scope of delivery.
Technical Data
Glue gun
Article number
Rated power input
– Heating
– Keeping the glue gun
warm
Heat-up time
Gluing temperature
Gluing capacity
Glue stick diameter
Glue stick length
A)
Weight
Protection class
A) Weight without mains connection cable and without mains plug
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Values can vary depending on the product, scope of application and
environmental conditions. To find out more, visit
www.bosch-professional.com/wac.
1 609 92A B47 | (22.11.2024)
Operation
Starting Operation
u
Switching On and Off
To switch on the glue gun, plug the mains plug into a plug
socket.
Allow the glue gun to heat up for approx. 7 min before start-
ing work. To do this, set the glue gun down on the support
bracket (3).
To switch off the glue gun, remove the mains plug from the
plug socket.
u
Continuous Operation
The glue gun can be operated continuously when the mains
plug is plugged in. The power indicator (7) must light up.
During breaks from work, set the glue gun down on the unfol-
ded support bracket (3).
Cable-Free Operation
It is possible to work without cables in conjunction with the
charging station (5) (accessory).
If the discharged adhesive becomes more viscous, heat up
the glue gun again in the charging station.
Working Advice
u
GKP 200 CE
0 601 950 7..
W 500
W 30
Only use adhesives that have been recommended by the
manufacturer of the glue gun and that are suitable for the
min 4
processing temperature.
°C 200
Adhesive bonds can become unstuck when they are affected
g/min 20
by moisture or heat.
mm 11
u
mm 45−200
The glue gun can also be used when it is switched off after
heating using the heat accumulator. If the discharged adhes-
kg 0.40
ive becomes more viscous, plug the mains plug back into the
/Ⅱ
plug socket.
Preparing for gluing
The bonding locations must be clean, dry and free from
grease.
The materials to be glued together and the work surface
must not be easily ignited or flammable.
Test whether heat-sensitive materials are suitable before-
hand on a sample workpiece.
Pay attention to the mains voltage! The voltage of the
power source must match the voltage specified on the
rating plate of the glue gun.
Safely place the glue gun down after use and let it cool
completely before packing it away. The hot nozzle can
cause damage.
Keep people and animals away from the hot adhesive
and the nozzle tip. Adhesive and nozzle tip will heat up to
approx. 200 °C, posing a risk of burns. If hot adhesive
comes into contact with skin, immediately hold the af-
fected area under a stream of cold water for several
minutes. Do not try to remove the hot adhesive from the
skin.
Remove the mains plug for longer work breaks.
Bosch Power Tools