Publicité
Watching the DVD
2 On the screen, "4" changes to "Reading" and then
Perform the following steps before you press POWER
* A menu screen appear on the TV screen, if ihe disc
on the remote control unit.
has a menu feature. In this case, press a/w/4/»
or
ae
;
ENTER to operate a menu feature.
1 Insert the batteries into the remote control unit.
3 Press STOP to end playback.
S
9.
(See Page.)
+ The unit memorizes the stopped point, depending on
2 Plug in the AC cord to the AC outlet. (See page 8.)
the disc. "Re appears on the screen. Press PLAY to
resume playback (from the scene point}.
Turning on the power
'
>
+ If you press STOP again ("W" appears on the screen)
Press
POWER on the TV/DVD, or P OWER aihe
A wee the disc, the TV/DVD will clear the stopped
remote control.
* POWER indicator (Green): The TV/DVD is on.
4 Press EJECT.
("Please wait" will appear for a few seconds on the
Remove the disc and then press POWER.
screen.)
The TV/DVD turns off.
oe
SE
sa
oia
ae oi o
+ When you eject the disc, you may hear mechanism
Select the DVD mode
noise, but it is not malfunciion.
Press TV/DVD to select the DVD mode.
Status display of DVD disc -
Turning off the powe
Press DISPLAY. The status display of the disc will
appear on the screen in order like the figure below.
Press POWER on the TV/DVD, or POWER on the
remote control.
+ The TV/DVD enters standby mode and the image on the
screen disappears.
* The POWER indicator on the TV/DVD changes to Red.
ELAPSED
TOTAL
DISC OPERATION
TIME
TIME
TITLENO,
| FR
CHAPTER
-if you are not going to use this TV/DVD for a long period
NO.
of time, be sure to remove the AC cord from the power
ouilet.
ff titra aft
S e s
+ Weak electric power is still consumed even when POWER
RENG
SUBTITLE LANGUAGE
is turned off.
AUDIO LANGUAGE
AKIND OF AUDIO
ESE?
If the TV/DVD does not operate properly:
Static electricity, ete., may affect the players operation.
Disconnect the AC power cord once, then connect it again.
1 Place the disc in the disc slot with the label side
facing forward. (If the disc has a label.) Hald the
disc without touching its surface, align it with the
guides, and place it in position.
* [fa disc is inserted during some modes other than DVD
mode, it may switch to DVD mode and then playback
may be begun automatically.
. if a non-compatible disc is loaded, "Incorrect Disc", "Region Code Error" or "Parental Error" will appear on the TV screen
according to the type of loaded disc. If these appear, check your disc again (see pages 5 and 32).
* Some discs may take a minute or so to start playback.
+ When an 8 cm disc is placed into the disc slot, and the playback picture or menu display does not appear, press PLAY,
+ A "Prohibition" symbol "X" may appear at the upper right of the screen. This symbol means either the feature you tried is
not available on the disc, or the TV/DVD cannot access the feature at this time. This does not indicate a problem with the
TV/DVD.
When you set a single-faced disc label downwards (¡.e. the wrong way up) "Reading" will appear on the display and then
"Incorrect Disc" will be displayed.
Some playback operations of DVDs may be intentionally fixed by software producers. Since this TV/DVD plays DVDs
according to the disc content recorded, some playback features may not be available. Also refer to the instructions supplied
with the DVDs.
Do not move the unit during playback. Doing so may damage the disc.
Use EJECT to unload and eject the disc.
Do not put any objects other than discs on the disc slot. Doing so may cause the unit to malfunction.
In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press
POWER on your remote control once the movie is completed.
* There may be a slight delay between the button is pressed and the function activates.
Publicité
