Manuels Connexes pour Panduit BlackFin CT-2920/CCPBT
Sommaire des Matières pour Panduit BlackFin CT-2920/CCPBT
- Page 1 Panduit Corp www.panduit.com/blackfi n CT-2920/CCPBT Instruction Manual Serialnumber Pic. similar HE.20204_A © 11/2021 R&D-2...
- Page 2 CT-2920/CCPBT PANDUIT CD-920 CD-930 optional: optional: BL1850(B) (RAL4) BL1840(B) (RAL40) BL1830(B) (RAL2) BL1815 (RAL1) datecode FCC ID: RFRMS42 • IC: 4957A-MS42 Model: CFM WARNING Year Code Month Code Month Code This device complies with Part 15 of the FCC Rules and with...
- Page 3 CT-2920/CCPBT 17,4“ 3“ 76mm 442,5mm 1,1“ 29mm CT-2920/CCPBT Multi Use Tool Voltage: 18 V • Force: 12.1 Ton (108kN) LISTED TOOL Gustav Klauke GmbH • Auf dem Knapp 46 80103907 42855 Remscheid Germany EK120UNVCFMPAN • For use only with 18 V Makita battery <70dB <2,5m/s +104°F...
- Page 4 CT-2920/CCPBT > 350° STOP 30% max. on/off Pic. similar / Intended Use General WORK SERVICE DON´T DO HE.20204_A © 11/2021 safety rules...
- Page 5 CT-2920/CCPBT Einsätze Anwendung Einsätze Anwendung Dies Application Dies Application PANDUIT CD-920 CD-930 NYY/NAYY UC26 Cu/Al < Ø 1.02“ (26 mm) UA12TKL NYY/NAYY UC40 Cu/Al < Ø 1.57“ (40 mm) UA12P (108 kN) ACSR UCACSR max. Ø 1.57“ (40 mm) UA12ID...
- Page 6 CT-2920/CCPBT UA12TKL see page IV PANDUIT CD-920 CD-930 UA12ID Pic. similar / Intended Use General WORK SERVICE DON´T DO HE.20204_A © 11/2021 safety rules...
- Page 7 CT-2920/CCPBT page IV page IV page IV page IV Cable Threaded Cutter Cutter >t <t reset Pic. similar / Intended Use General WORK SERVICE DON´T DO HE.20204_A © 11/2021 safety rules...
- Page 8 CT-2920/CCPBT Error codes: USER 3: 1 Overcurrent fuse Doubleclick D op p e l k l i c k 2 Overcurrent comparator 3 Overheat board 4 Overheat battery 5 Battery empty, operation stop 6 Faulty crimp U SE R S E L E C T: Singleclick motor in operation R D3...
- Page 9 CT-2920/CCPBT BEFORE WORK DIN EN 50110 HE.17441 SAFETY 3 years or 10.000 operations Authorised Service Center Authorised Service Center Authorised WEEE 2012/19/EU Service klauke-weee-abholung@emerson.com Center Authorised Service Center https://www.klauke.com/de/en/service-centre-and-repairs Pic. similar / Intended Use General WORK SERVICE DON´T DO HE.20204_A ©...
- Page 10 CT-2920/CCPBT Wann/When/Quand/Quando/ Warum/Why/Pourqoui/Porquê/ cuándo/Wanneer/Когда/это ¿por qué?/Waarom/Причина/ происходит/Kiedy/quando Dlaczego/Perché nach Arbeitsvorgang after working cycle après opération de travail Después del proceso de trabajo após o processo de trabalho 20 sec na bedrijfscyclus после цикла опрессовки po zakończeniu pracy dopo il processo di lavoro nach Arbeitsvorgang after working cycle après opération de travail...
- Page 11 System Verbindungen mit Power of Partnership CT-2920/CCPBT Declaration of conformity (D) CE-´21 - Konformitätserklärung. Wir erklären in alleiniger Verantwortlichkeit, (DK) CE-´21 - Konformitetserklæring. Vi erklærer under almindeligt ansvardt dass dieses Produkt mit den folgenden Normen oder normativen Dokumenten at dette produkt er i overensstemmelse med folgende normer eller normative übereinstimmt: dokumenter: EN 62841-1, EN ISO 12100, EN ISO 13857, EN ISO 13854, EN 28662-1,...
- Page 12 System Verbindungen mit Power of Partnership CT-2920/CCPBT Declaration of conformity (D) CE-´21 - Konformitätserklärung RED. Wir erklären in alleiniger (N) CE-´21 - Konformitetserklæring RED. Vi erklærer på eget ansvarlighet Verantwortlichkeit, daß dieses Produkt mit den folgenden Normen oder at dette produkt er i overensstemmelse med følgende standarder eller normativen Dokumenten übereinstimmt: standard-dokumenter: EN 62368-1, EN 301489-1, EN 301489-17, EN 300328 V2.2.2, EN 62479...
- Page 13 11. The fi nal inspection is carried out by the Service Center Goods Department The user of the Panduit product is responsible for verifying suitability of the product for the application and assumes all risk and liability in connection with its use.