Publicité
Operating Instructions
Solar Wall Light with PIR Sensor
Item no: 2813286
1 Intended use
The product is an LED lamp with motion sensor and light sensor. There are three lighting
modes, and the battery is recharged by the solar panel.
The product has an IP44 ingress protection rating. It is splash proof and suitable for outdoor
use. Do not submerge in water.
If you use the product for purposes other than those described, the product may be dam-
aged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product
available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights
reserved.
2 Delivery contents
■
Product
■
2x Mounting screws
3 Latest product information
Download the latest product information at
code shown. Follow the instructions on the website.
4 Description of symbols
The following symbols are on the product/appliance or are used in the text:
The symbol warns of hazards that
can lead to personal injury.
This product is constructed accord-
ing to protection class III.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
■
If you have questions which remain unanswered by this information product, contact our
technical support service or other technical personnel.
■
Maintenance, modifications and repairs must only be completed by a technician or an
authorised repair centre.
5.2 Handling
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
5.3 Operating environment
■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam
and solvents.
5.4 Operation
■
Consult an expert when in doubt about the operation, safety or connection of the
product.
■
If it is no longer possible to operate the product safely, take it out of operation and pro-
tect it from any accidental use. DO NOT attempt to repair the product yourself. Safe op-
eration can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
5.5 Li-ion battery
■
The rechargeable battery is permanently built into the product and cannot be replaced.
3
■
2x Dowels
■
Operating instructions
www.conrad.com/downloads
or scan the QR
The symbol warns of dangerous
voltage that can lead to personal in-
jury by electric shock.
Read the operating instructions
carefully.
■
Never damage the rechargeable battery. Damaging the casing of the rechargeable bat-
tery might cause an explosion or a fire!
■
Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or
the product into fire. There is a danger of fire and explosion!
■
Charge the rechargeable battery regularly, even if you do are not using the product. Due
to the rechargeable battery technology being used, you do not need to discharge the re-
chargeable battery first.
■
When charging, place the product on a surface that is not heat-sensitive. It is normal that
a certain amount of heat is generated during charging.
5.6 LED light
■
Do not look directly into the LED light!
■
Do not look into the beam directly or with optical instruments!
5.7 Installation
■
When penetrating the surface e.g. drilling or inserting fasteners, make sure no cables or
pipes are damaged.
■
Inadvertently penetrating electric cables causes the life-threatening danger of an electric
shock!
6 Product overview
1
1
Mode button
3
Solar panel
5
Light panel
7 Chosing a location
Find a location that exposes the solar module to full sunlight to allow the rechargeable bat-
tery to recharge during the day.
Consider the following:
■
The solar panel should be exposed to maximum sunlight. Do not set up the product in
the shade or under any cover.
■
Avoid the direct proximity of other light sources such as yard or streetlights, otherwise
the product will not switch on automatically at nightfall.
8 Wall mount
When penetrating the surface e.g. drilling or inserting fasteners, make sure no
cables or pipes are damaged. Inadvertently penetrating electric cables causes the
life-threatening danger of an electric shock!
1. Use the mounting plate as a template to mark holes on the surface.
2. Drill holes on the marked positions.
3. Attach the product using the supplied dowels and screws.
à
If hanging the product, leave some of the screw protruding from the mounting surface.
à
Make sure the product is securely mounted before letting go.
9 Recharge batteries
Important:
To maximize charging efficiency, keep the solar panel(s) clean and free from debris.
■
Solar charge the battery under bright sunlight for at least 8 hours:
– Before first use
– After prolonged periods without exposure to sunlight e.g. rain.
10 Operation
Note:
There is an integrated light sensor that responds to ambient light levels. The product will
be active when ambient light falls below a set level (nighttime). The product will deactiv-
ate when the ambient light rises above a set level (daytime).
2
3
4
5
2
Mounting hole
4
Motion sensor
Publicité
