POLTI SV240 Manuel D'instructions page 18

WARNING: If the ignition/steam-adjustment
dial has been turned from the "OFF"
position, by inserting the handle tube in
the coupling hole, the appliance will start
immediately to emit steam. Always face
the appliance downwards, not directing it
towards people, animals or objects.
5.2 About 30 seconds after it has been
turned on, the appliance will start to dispense
steam.
5.3 Clean the floors by moving the brush.
WARNING: Do not use the appliance
without the cloth.
WARNING: To remove the cloth from the
brush, turn the ignition/steam-adjustment
dial to the "OFF" position, unplug the
power supply from the electric socket and
wait a few minutes to allow the cloth to
cool.
WARNING: For additional safety, test steam
delivery on a hidden part, leave the steamed
part to dry to ensure that no changes in
colour or deformation have occurred.
6. CLEANING RUGS AND
CARPETS
WARNING: Before steam treating surfaces
(wood or laminate floors, carpets, rugs,
leather and fabrics and any surfaces
especially those
treated), consult the surface manufacturer's
or the supplier/installer's instructions and
always perform a test on a section that
is out of view or on a sample. Allow the
steamed surface to dry to ensure that there
is no deterioration, change of colour or
deformation and that the surface stands up
to the temperature of the steam.
Before using the appliance on delicate
surfaces, ensure that the part in contact
with the surface is free from foreign bodies
that could cause scratches.
Ensure that the points in Sections 1 and 2 have
been followed.
6.1 To clean rugs and carpets, rest the brush
(with the cloth attached) on the special frame
so that it can slide over the surface (6).
6.2 Turn the ignition/steam-adjustment dial
clockwise, from the "OFF" position to one
of the three steam-adjustment positions; for
this type of surface, use the Medium level of
steam.
that are delicate
The "steam ready" indicator light will come on
to indicate that the appliance is on (heating).
WARNING: If the ignition/steam-adjustment
dial has been turned from the "OFF"
position, by inserting the handle tube in
the coupling hole, the appliance will start
immediately to emit steam. Always face
the appliance downwards, not directing it
towards people, animals or objects.
6.3 About 30 seconds after it has been turned
on, the appliance will start to dispense steam.
6.4 Clean the floors by moving the brush.
WARNING: Do not use the appliance
without the cloth.
WARNING: To remove the cloth from the
brush, turn the ignition/steam-adjustment
dial to the "OFF" position, unplug the
power supply from the electric socket and
wait a few minutes to allow the cloth to
cool.
WARNING: For additional safety, test steam
delivery on a hidden part, leave the steamed
part to dry to ensure that no changes in
colour or deformation have occurred.
7. CLEANING BATHROOM
FIXTURES, GROUTING AND
KITCHEN WORKTOPS, BARBECUE
Make sure that chapter 1 has been completed.
or
Only use the steam gun.
7.1 Connect the lance to the steam gun (12).
To connect the accessory to the accessory-
connection socket,
accessory-locking button clicks.
7.2 Connect the most suitable accessory
depending on the need (13):
• round brushes to remove encrusted dirt.
• grout accessory to clean between tiles or to
remove dirt from very narrow surfaces.
7.3 Plug the power lead into a suitable
socket with an earth connection.
7.4 Turn the ignition/steam-adjustment dial
clockwise, from the "OFF" position to one of
the three steam-adjustment positions; for this
type of surface, we recommend the Maximum
level of steam.
The "steam ready" indicator light will come on
to indicate that the appliance is on (heating).
7.5 About 30 seconds after it has been
turned on, the appliance will start to dispense
steam.
7.6 Thoroughly steam the surface to dissolve
the dirt. Use a dry cloth to remove the dirt
dissolved by the steam.
| 18 |
just insert until the