DeWalt DWE627 Traduction De La Notice D'instructions Originale page 36

EngLIsH
On/Off Trigger Switch (Fig. A)

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
1. To turn the unit on, squeeze the on/off trigger switch
Continue to squeeze the trigger switch or press the lock on
button switch 20 for continuous running.
2. To turn the unit off:
a. If lock on trigger is engage, release the lock on button by
squeezing and releasing trigger.
b. If the lock on switch is not engage, fully release the trigger.
Variable Speed Dial (Fig. A)

WARNING: If the speed control ceases to operate, or is
intermittent, stop using the tool immediately. Take it to a
D WALT factory or authorized service facility for repair.
e
NOTICE: The router is equipped with electronics to
monitor and maintain the speed of the tool while cutting.
In low and medium speed operation, the speed control
prevents the motor speed from decreasing. If you expect
to hear a speed change and continue to load the motor,
you could damage the motor by overheating. Reduce
the depth of cut and/or slow the feed rate to prevent
tool damage.
Refer to the Speed Selection Chart to choose a router speed.
Turn the speed dial 1 to control router speed. The speed is
variable from 9000 to 22000 rpm using the speed dial
1. Turn the speed dial to the required position. The dial is
numbered from 1 –7 and corresponds to router speeds of
9000 rpm to 22000 rpm.
2. Use the slower settings for large diameter cutters and the
faster settings for small diameter cutters.
3. The correct setting will also depend on the density of the
material, depth of cut and feed speed of the router.
nOtE: A noticeable loss of motor rpm means
motor overload.
SPEED SELECTION CHART
DIAL SETTING
1
2
3
4
5
6
7
The speeds in this chart are approximate and are for reference
only. Your router may not produce the exact speed listed for the
dial setting.
34
3 .
1 .
APPROXIMATE RPM
9000
11000
13000
15000
18000
20000
22000

WARNING: Always follow the bit manufacturer's speed
recommendations as some bit designs require specific
speeds for safety or performance.
If you are unsure of the proper speed or are experiencing any
type of problem, contact the bit manufacturer.
n
LED Worklight (Fig. F)

CAUTION: Do not stare into worklight. Serious eye
injury could result.
Two LED worklights 57 are located next to the collet assembly
1. The worklights 57 will constantly illuminate when the
router is connected to the mains power supply.
2. To switch off the worklights the router must be
disconnected from mains power supply.
nOtE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Setting Plunge Lock System (Fig. B)
The plunge is fully automatically locking for all cuts. For heavy
cut operations, ensure to push the lever towards the tool body.
The plunge lock lever 6 position is set at the factory so the
lever does not touch the motor body, if the plunge lock lever
begins to hit the body when the quick release lever is pushed,
readjust the locking lever position as follows:
1. Push in quick release button
unlock automatically.
2. Using a Torx 20 star bit
on the plunge lock lever
Do not fully remove.
3. Lift the plunge lock lever, rotate and reposition the plunge
lock lever at position 2 (at eleven o'clock).
4. Tighten the shoulder screw.
5. If after setting to position 2 sliding is not correct, repeat
steps 1 to 3 and reposition the lock lever at position 1.
Tighten the shoulder screw.
Moulding Natural Timbers

WARNING: When routing always lock the plunge
locking lever.
When edge moulding natural timbers, always mould the end
grain first, followed by the long grain. This ensures that if there is
breakout, it will be removed when the long grain is routed.
Setting the Routing Depth (Fig. D, E)
1. Place the router with cutter fitted on to the workpiece.
2. Set the multiple position turret stop
3. Loosen the knob quick adjustment
depth stop 12 .
4. Push down the plunging lock lever
5. Lower the router slowly until the cutter touches
the workpiece and secure it in place by pushing
quick release button 7
7 . The plunge lever lock will
39 , loosen the shoulder screw
6 with six counterclockwise turns.
11 as required.
15 securing the
6 to start plunging.
.
9 .
54