Télécharger Imprimer la page

DeWalt DWE627 Traduction De La Notice D'instructions Originale page 34

Publicité

EngLIsH
Installing and Removing a Cutter (Fig. C, F)

WARNING: Do not tighten the collet without a
cutter fitted.

WARNING: Always use cutters with shanks which match
the diameter of the collet.

WARNING: Do not use cutters larger than 50 mm (2")
unless the router is fitted in a router table.

CAUTION: Care should be taken when removing cutter to
avoid cuts to fingers.
Installing a Cutter
1. Insert at least three fourths of the shank length of the cutter
into the collet assembly 
2. Press the spindle lock 
 8 
is locked.
nOtE: You may need to turn the spindle slightly to
engage it.
3. Turn the collet nut 
 36 
22 mm wrench 
 13 
to tighten it.
Removing a Cutter
1. Press the spindle lock button 
spindle is lock.
2. Turn the collet nut 
 9 
clockwise with the supplied 22 mm
wrench 
 13 
to loosen.
3. Keep turning the wrench until the collet nut tightens and
then loosens again. This is the fail‑safe mechanism releasing
the collet.
4. The cutter should now slide out.
nOtE: Each time you finish using a cutter, remove it and
store it in a safe place.
Fine Height Adjuster (Fig. A, D, E)

CAUTION: Ensure that the plunge locking lever is
unlocked. Never use unnecessary force to rotate the fine
height adjuster mechanism.

CAUTION: Do not remove the screw on hex nuts.
The fine height adjuster can be used in portable mode or when
the router is held inside a table.
Adjusting the Depth of Cut (Fig. A, D, E)
Your router is equipped with a high‑precision depth adjustment
system including a zero reset ring for both the quick height
adjuster and the fine height adjuster.
Quick adjustment Using the graduation with Zero Reset Ring
1. Loosen the depth stop quick height adjuster lock 
2. Unlock the plunge limiter by pushing the release
lever 
 6 
 down.
3. Lower the router carriage until the cutter is in contact with
the workpiece.
4. Press the quick locking button 
5. Set the quick height adjuster 
adjust reset ring 
 19 
to zero. The depth stop bar 
in contact with the turret stop 
32
 9 
.
forward until the router spindle
counterclockwise with the supplied
 8 
forward until the router
 15 
 7 
.
 16 
to zero and reset the fine
 12 
 11 
.
6. Adjust the depth of cut using the quick height adjuster 
and the corresponding graduation. The adjusted depth of
cut is indicated by the pointer 
7. Tighten the quick height adjuster lock 
Fine adjustment
When not using a depth template, or if the depth of cut
needs readjustment, it is recommended to use the fine height
adjuster 
 18 
.
1. Adjust the depth of cut as described in Adjusting the Depth
of Cut.
2. Set the fine height adjuster to zero using the fine zero reset
ring 
 19 
3. Rotate the fine height adjuster 
position: one turn corresponds to approximately 1 mm and
1 mark to 0.1 mm.
Fitting a Guide Bush (Fig. H)
Together with a template, guide bushes play a valuable part in
cutting and shaping to a pattern.
Fit the guide bush 
screws 
 25 
Fitting the Parallel Fence (Fig. I, J)
1. Fit the guide rod 
2. Slide the parallel fence 
3. Tighten the wing bolts 
Adjusting the Parallel Fence (Fig. A, I, J)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in contact with
the workpiece.
3. Push quick release button 
using the thumb wheel 
4. Position the router on the cutting line.
5. Slide the parallel fence 
tighten the wing bolts 
6. Adjust the parallel fence using the fine adjustment knob 
The outer cutting edge of the cutter must coincide with the
cutting line.
7. If required, loosen the screws 
to obtain the desired guiding length.
Dust Extraction (Fig. A, K, P)
Dust from materials such as lead‑containing coatings and some
wood types, can be harmful to one's health. Breathing‑in the
.
dust can cause allergic reactions and/or lead to respiratory
infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered
carcinogenic, especially in connection with
wood‑treatment additives.
Observe the relevant regulations in your country for the
materials to be worked.
The vacuum cleaner must be suitable for the material
must be
being worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use dust class M vacuum cleaner.
 17 
.
 18 
to the required
 24 
to the router base 
as shown.
 26 
to the router base 
 27 
over the rods.
 28 
 temporarily.
 7 
and limit the carriage return
 4 
.
 27 
against the workpiece and
 28 
.
 30 
and adjust the strips 
 16 
 15 
.
 10 
using the
 10 
.
 29 
.
 31 

Publicité

loading

Ce manuel est également adapté pour:

Dwe625Dwe627kt