Publicité
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 12)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
2. Layout and items supplied
2.1 Layout (Fig. 1)
1. On/Off switch
2. Speed controller
3. Locking knob for collet chuck
4. Clamp nut
5. Cover
6. Equipment holder
7. Flexible shaft
Anl_TC_MT_150_E_SPK13.indb 14
Anl_TC_MT_150_E_SPK13.indb 14
GB
2.2 Items supplied (Fig. 1-2)
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
1x grinding and engraving tool
•
1x equipment holder (6)
•
1x flexible shaft (7)
•
6x drill bit, 1.6 / 2.4 / 3.2 mm (8)
•
6x grinding pin, glass/stone/ceramic, various
shapes (9)
•
5x cutting pin, various shapes (10)
•
6x grinding pin, metal, various shapes (11)
•
1x cup brush (12)
•
1x round brush (13)
•
3x cutting wheel, large/medium/small (14)
•
36x grinding belt, large/small (15)
•
1x chuck key (16)
•
2x clamping spindle (17)
•
1x arbor (18)
•
4x grinding wheel, large/small (19)
•
10x felt polisher, large/small/high (20)
•
20x grinding wheel, red/green (21)
•
10x cutting wheel (22)
•
6x clamping sleeve, 1.6 / 2.4 / 3.2 mm (23)
•
3x clamp nut (24)
•
Original operating instructions
•
Safety information
- 14 -
07.05.2024 13:30:39
07.05.2024 13:30:39
Publicité
