Publicité
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (5) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (6) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (5), press the release button (6) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Bosch Power Tools
https://tm.by
Интернет-магазин TM.by
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Inserting the Bluetooth® Low Energy Module
GCY 42 (Accessory)
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Changing the Tool (see figures A–C)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Regularly clean the power tool's air vents. The motor's
u
fan can draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
When working with an application tool, pay attention
u
that the application tool is connected securely to the
tool holder. When the application tool is not securely
connected with the tool holder, it can come off during ap-
plication.
Slide the application tool (10) onto the square drive of the
tool holder (1).
Removing the application tool (see figure C)
to
GDS 18V-1000 PC:
Use a auxiliary tool (e.g. a needle) to remove the application
tool.
Operation
Method of Operation
The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
Capacity
The working procedure is divided into two phases:
60−100 %
Screwing in and tightening (impact mechanism in action).
30−60 %
The impact mechanism is activated as soon as the screwed
connection runs tight and load is therefore put on the motor.
5−30 %
The impact mechanism then converts the power of the mo-
0−5 %
tor to steady rotary impacts. When loosening screws or nuts,
the process is reversed.
English | 19
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
1 609 92A 5N5 | (06.08.2020)
Publicité
