System Start-Up; Preliminary Checks: Inputs - Weight Class - Pinion Type - M/S Configuration - Opening Direction; Self-Teaching - Aprimatic SLIDE 230 APRICODE Instructions D'installation, D'utilisation Et D'entretien

CONTROL UNIT
3.

SYSTEM START-UP

When the power supply to the unit is switched ON,
the following information is shown on the display: the
FIRMWARE release NUMBER and the NAME of the system.
When the display switch OFF the unit can be operated.
When the power supply is switched ON to the unit for the
fi rst time, the display shows
• To press the YELLOW and BLUE buttons simultaneously for
Lrn
approximately 3 seconds
to perform the
PRELIMINARY CHECKS
Lrn Lrn
=
: fl ashes on the display.
3.1 Preliminary checks: inputs - Weight class - Pinion
type - M/S confi guration - opening direction
To access to the programming press the RED button.
INPUTS
Lrn
During , the fourth display on the unit shows the input state (fi g.2).
WEIGHT CLASS - PINION TYPE
Lrn
During , access to programming (see fi g.4 and par. Parameter
programming) to modify, if necessary, the following parameters:
CP
depending on the wing weight
Mod
depending on the installed type of pinion
MASTER/SLAVE CONFIGURATION
When two automations are connected to each other in M/S mode,
MS
the parameter must be appropriately enabled on both control
units. This allows you to apply the controls on both the installations.
!
Warning
To connect the START and STOP inputs to the Master unit.
OPENING DIRECTION (OPEN / CLOSE)
Lrn
During , when the gate is closed, to verify that (fi g.3):
- YELLOW button
FIRST PRESSION
Otherwise it will be necessary to correct the parameter
NOTE: the M/S wings must have opposite opening direction.
3.2

Self-teaching

Lrn
During , give a START command
and closes in succession, then the self-teach procedure ends:
the gate will stop closed and the displays will switch OFF.
!
Warning
External signals are ignored during the self-teach procedure
except for the installed safety devices and STOP signals. If
these signals are triggered the self-teach procedure is stopped
and must be repeated.
PLEASE SEE THE ERROR CODES IN CASE THE SELF
( .
STOPPED PAR CHECKS AND WARNINGS ON DISPLAY
Operation is now possible using the key button or a
programmed remote control unit to check correct functioning.
NOTE: after the self-teach procedure the default functioning
mode is AUTOMATIC (see the par. Operating logics). See
the section "Programming the parameters" to know the
factory settings.
Init
; it is necessary:
fl ashes on the display; it is necessary
and the - procedure.
SELF TEACH
OPEN.
the gate opens completely
-
TEACH PROCEDURE IS
).
SLIDE 230 APRICODE
fi g. 2 - Check on the state of the inputs during
Lrn
display 4 during
(segment ON = contact closed)
L r N _ -
1 = START RADIO
2 = CLOSING PHOTOCELL
4 = PEDESTRIAN START
5 = SAFETY DEVICE during OPENING
6 = START
7 = STOP
During standby, segments 2, 7 and 5 fl ash if the relevant
connections or jumpers are correct.
fi g. 3 - Special operation during
Lrn
Display during
Each time the button is released and then pressed again,
the movement of the wing is reversed.
fi g. 4 - Access to programming during
Lrn
Display during
d1
.
fi g. 5 - SELF-TEACHING movements
Start the self-teach movements:
L r N _ -
display during LRn
Searching closing limit switch
Complete opening
Complete closing
The gate is closed
note: during the self-teaching the automation can be stopped
Lrn
and the phase re-accessed: simply activate an installed
safety device or press the STOP control if connected.
: at anytime, the self-teaching can be activated: press the
NOTE
and buttons simultaneously for approximately
YELLOW BLUE
Lrn
3 seconds.
- 20 -
: INPUTS
2
1
7
6 4
5
lrn
status:
L r N _ -
:
YELLOW
MOVES THE GATE
lrn
L r N _ -
:
RED
PROGRAMMING
LO 0
.
START
FA 1
Display:
FA 2
Display:
FA 3
Display:
Display switched OFF
fl ashes on the display.
L r N _ -
3 "
lrn