Publicité
EN
6
Before Using for the First Time
1. Remove all packaging materials.
2. Remove any stickers or labels from the appliance .
3. thoroughly clean the fried plate and pot with hot water, some washing-up liquid and a non-abra-
sive sponge.
4. Wipe inside and outside of the appliance with a moist cloth.
This is an oil-free fryer that works on hot air, Do not fill the pot with oil or frying fat directly.
Notice: When your air fryer is heated for the first time, it may emit slight smoke or odor.
This is normal with many heating appliances. This does not affect the safety of your
appliance.
Preparing for use
1. Place the appliance on a stable, horizontal and even surface.
Do not place the appliance on non-heat-resistant surface.
2. Place the fried plate in the pot (Fig.4).
Do not fill the pot with oil or any other liquid.
Do not put anything on top of the appliance, the airflow will be disrupted and affects the
hot air frying result.
Using the appliance
The oil-free can prepare a large range of ingredients.
Hot air frying
1. Connect the mains plug into an earthed wall socket.
2. Carefully pull the pot out of the Hot-air fryer (Fig.3)
3. Put the ingredients in the po. (Fig.4)
4. Slide the pot back into the Hot-air fryer (Fig 5)
Noting to carefully align with the guides in the body of the fryer.
Never use the pot without the Fried plate in it.
Caution: Do not touch the pot during and some time after use, as it gets very hot. Only hold
the pot by the handle.
5. Determine the required preparation time for the ingredient ( see section 'Settings' in this chap-
ter).
6. Some ingredients require shaking halfway through the preparation time (see section "Settings" in
this chapter). To shake the ingredients, pull the pot out of the appliance by the handle and shake
it. Then slide the pot back into the air fryer
caution: Do not press the button the handle during shaking.
Tip: To reduce the weight, you can remove the basket from the pot and shake the basket only. To
do so, pull the pot out of the appliance, place it on a heat-resistant surface and press the button of
handle. and lift the basket out of the pot
Tip: If you set the timer to half the preparation time, you hear the timer buzzer when you have to
shake the ingredients. However, this means that you have to set the timer again to the remaining
preparation time after shaking.
7. When you hear the timer buzzer, the set preparation time has elapsed. Pull the pot out of the
appliance
Note: You can also switch off the appliance manually. To do this, set the time to 1.
Tip: You can adjust temperature or time according to your taste during use. Your settings will be
kept for about 10 mins after you pull the pot out of the body.
8. Check if the ingredients are ready. If the ingredients are not ready yet, simply slide the pot back
into the appliance and set the timer to a few extra minutes.
9. To remove ingredients (e.g. fries), pull the pot out of the Hot-air fryer and place it on trial frame-
work,
Do not turn the Fried plate upside down with the pot still attached to it, as any excess oil
that has collected on the bottom of the pot will leak onto the ingredients.
The pot and the ingredients are hot. Depending on the type of the ingredients in the air
fryer, steam may escape from the pot.
10. Empty the basket into a bowl or onto a plate.
11. When a batch of ingredients is ready, the Hot-air fryer is instantly ready for preparing another
batch.
Control panel instructions
1. Plug the appliance into the wall socket. All lights will illuminate briefly and the timer will beep.
The power button
light stays on.
2. Short press the power button
to turn on the device. The 8 standard programs light up and
the displays show '--'.
3. Select
and then
to use tray 1. The power button
will flash. The tray 1 display alternates between the default settings of 180°C/15 minutes. Both
displays are on, but when tray 2 is not used, the display for tray 2 shows "---".
4. Click the menu button
to select the desired menu. The menu button lights up and the
temperature is shown on the display. After 3 seconds, the temperature and time are displayed
alternately. Click the temperature-time button
tons
to set the temperature or time and press the power button
up. When the appliance is in operation, the menu button lights up and the temperature and time
7
and the appropriate menu button
to set the temperature or time. Press the but-
. The lamp lights
EN
Publicité
