Publicité
English
pack is removed. Unexpected starting of the machine while
clearing jammed material or servicing may result in serious
personal injury.
Additional Safety Information
a ) Always use the shoulder harness when operating.
b ) Do not use for edging. This is not an edger.
c ) KEEP ALL BYSTANDERS AWAY – at a safe distance
from work area, especially children. MAKE SURE that
other persons and pets are at least 100' (30 m) away.
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
WARNING: Do not modify or attempt to repair the
appliance or the battery pack except as indicated in the
instructions for use and care.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses
are NOT safety glasses. Also use face or dust mask if operation is
dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust contains chemicals known to
State of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• compounds in fertilizers,
• compounds in insecticides, herbicides and pesticides,
• arsenic and chromium from chemically treated lumber.
To reduce your exposure to these chemicals, wear approved
safety equipment such as dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing dust
to get into your mouth, eyes, or lie on the skin may promote
absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or
disperse dust, which may cause serious and permanent
respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.
CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a tripping
or falling hazard. Some tools with a large battery pack will
stand upright but may be easily knocked over.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V .......................... volts
Hz ........................hertz
min ......................minutes
or DC ......direct current
....................... Class I Construction
(grounded)
.../min .............. per minute
10
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per minute
RPM .................... revolutions per minute
sfpm ................... surface feet per minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
...................... wear eye protection
...................... wear hand
protection
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Mounting the Bike Handle (Fig. B–G)
1. Unthread the handle clamp screw
it counterclockwise until the handle clamp
removed from the handle mount
nOTE: Do not lose the clamp screw spring
2. Place the bike handle
clamp
and then place the upper handle clamp
23
on top of the bike handle
clamp
23
as shown in Fig. C.
3. Place the handle clamp screw
clamp assembly. With one hand holding the handle clamp
assembly, use your other hand to guide the clamp screw
spring
onto the handle clamp screw
22
clamp screw
12
into the handle mount
nOTE: Ensure the clamp screw spring
securing the handle clamp assembly.
4. Loosely tighten the handle clamp screw
it clockwise until the handle clamp
on the handle mount
25
tighten the handle clamp screw
5. Rotate the bike handle
shown in Fig. E and F. Adjust it so that the distance "A" is
roughly 7" (17 cm) as shown in Fig. F.
6. Fully tighten the handle clamp screw
the handle is secured in position before operating the unit
as shown in Fig. G.
Folding the Bike Handle (Fig. D–G)
Folding:
1. Unthread the handle clamp screw
it counterclockwise until the handle clamp
rotated counterclockwise.
nOTE: Do not fully loosen the clamp screw
...................... wear slip resistant
footwear
...................... wear head
protection
...................... wear hearing
protection
...................... read user manual
...................... do not expose
to rain
................. do not use
flexible line
................. do not use
metal blades
...................... beware of
thrown objects
............. the distance between
the machine and
bystanders shall be
at least 100 ft (30 m)
...................... beware of
blade thrust
...................... disconnect battery
before maintenance
12
by turning
21
can be
25
as shown in Fig. B.
.
22
4
on top of the lower handle
4
and into the lower handle
12
through the handle
. Place the handle
12
25
on the pole
22
is in place before
12
by turning
21
can still be moved
as shown in Fig. D. Do not fully
12
at this point.
up to its working position as
4
12
. Ensure that
12
by turning
can be
21
12
.
24
10
.
Publicité
