Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Charging the Display
When the display and handle are connected, the bat-
tery pack will power both the handle and the display.
When separated, the display runs off of an internal re-
chargeable battery. To recharge the display, connect
it to the handle/battery pack, or to a power source via
USB cable. Always store the display docked on the
handle. If the display shuts down due to low power,
recharge for at least 30 minutes before use.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Connecting the Cable
1. Slide back the socket sleeve.
2. Insert the cable into the socket.
3. Rotate the cable until it is fully seated into the
socket.
4. Slide the sleeve over the connection. Tighten the
sleeve securely.
Connecting the PIVOTVIEW™ Cable
(Some Models or as an Accessory)
1. Rotate the pivot knob to determine the orientation
needed for the movement. The pivot head rotates
up to 270º on one plane.
2. Snap the PIVOTVIEW™ Cable over the socket. It
must line up in one of four 90° positions.
3. To remove, press the release buttons and pull
away from the tool.
Inserting/Removing the Memory Card
The number of images/videos that can be saved is
based on the size of the memory card.
1. Open the protective cover to
access the memory card slot.
2. Slide the memory card into the
slot, the top of the card should
face away from the LCD screen.
Press in the card securely. It
should click in place.
3. Close the protective cover.
4. To remove the memory card,
press it in and release. It will pop out.
NOTE: To save images/videos to the memory card,
it must not be "locked" with the write-protection tab
in the lower position.
Downloading to a Computer
Insert the USB cable into the port on the side of the
display. Turn on the display. Connect the USB end
into the USB port on your computer.
NOTE: If you are unable to view the videos on your
computer it may be because your computer is miss-
ing the DIVX or XVID codec. The AVI file is recorded
in MPEG4 format and your computer needs a DIVX
or XVID codec to decode and play it. Download the
appropriate codec to view the images/videos.
To enter the settings menu, turn on the tool and
press the Settings button. Use the ◄►▲▼ buttons
to move through the setting menu.
MENU
MICROPHONE
LCD BRIGHTNESS
DATE
TIME
LANGUAGE
DELETE ALL
VERSION
OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields.
Always remove battery pack before changing
accessories or making adjustments.
Turning On/Off
When the display is docked on the handle, press
either Power
button to turn the tool on. Press and
hold either Power
When the display and handle are separated, use the
individual power buttons to turn each piece on and off.
When the display is docked on the handle, the
M12™ battery pack fuel gauge is displayed in the
upper right corner.
When the display is undocked from the handle, two
fuel gauges are displayed. The left gauge shows the
remaining charge of the display's internal battery.
The right gauge shows the remaining charge of the
M12™ battery pack. Each block in the fuel gauges
represents approximately 1/4 of the battery's life.
To reduce the risk of explosion,
WARNING
electric shock and property dam-
age, always check the work area before beginning
a job. Do not allow cable to contact electrical,
chemical, or moving hazards.
Behind walls: Shut off circuit breakers to the
entire area.
Inside Pipes: Ensure there is no electrical charge
to the pipes before beginning inspection. Do not
allow liquid to flow down cable and into tool.
Auto use: Turn off the engine and allow to cool
before beginning inspection. Do not allow the
visual inspection camera or cable to contact oil,
gas, or other corrosive materials.
To reduce the risk of damage to the
CAUTION
tool, do not use excessive force or
"kink" the cable. Do not use in areas where vi-
sual inspection camera and cable will contact
corrosive or oily substances.
Do not use the cable to clear clogs or move ob-
structions. This is not a drain cleaner!
Using the Handle and Display
To separate the display from the handle grasp each
part firmly and slide the display away from the battery
pack. To reconnect, slide handle and display together.
NOTE: The error message "NO IMAGE SIGNAL" is
displayed if the handle is not powered on, the handle
is out of range of the display (approximately 15') or
the cable is not fully connected to the handle. Also,
interference may occur when multiple tools are in
use in close proximity.
4
Settings
SELECTIONS
____________
ON/OFF
LOW/MEDIUM/HIGH
MM/DD/YY
HR/MIN AM/PM
MULTIPLE SELECTIONS
CANCEL/DELETE ALL
Display the software version.
button to turn the tool off.
Fuel Gauge
Publicité
Table des Matières
