Publicité
18
| English
IDENTIFICATION
1. Handle
2. Power cord hook
3. Switch ON/OFF
4. Power cord
5. Water outlet
6. Wheel
7. High-pressure hose reel
8. High-pressure hose
9. Trigger gun
10. Trigger gun hook
11. Rear case
12. Detergent tank
13. Lance with adjustable spray nozzle
14. Water inlet
15. Release trigger gun button
16. Rotary lance
17. Trigger gun protector
18. Short high pressure hose
ASSEMBLY
A. Slide the handle into position with two screws.
B. Slide the trigger gun holder into position.
C. Installing the trigger gun protection.
D. Locate to storage the power cable.
E. Assembling lance.
F. Connect the high pressure hose to the trigger
gun.
G. Disconnect the pressure hose.
H. Connect the short high pressure hose (18) to
the water outlet of the machine and to the con-
nection of the hose reel (7).
I. Connect the garden hose to the water inlet.
ATTENTION! ALWAYS USE A WATER FILTER.
Connect the water supply.
ATTENTION! Impurities in the water can dam-
age the high-pressure pump and the accessories
USE WITH ALTERNATIVE WATER SOURCES
The power washer is self-priming and enables wa-
ter to be drawn in from containers or natural wa-
ter sources. It is IMPORTANT that the water filter
is in clean condition when inserting it at the water
inlet, and that only clean water is drawn in.
OPEN TANKS/CONTAINERS AND NATURAL WA-
TER SOURCES
Use the Self Priming accessory kit comprising:
Inlet strainer with non return valve
ƒ
3m reinforced supply hose
ƒ
Universal coupling to the pressure washer
ƒ
This enables the pressure washer to draw water up
to 0,5 m above the water level in the source in ap-
proximately 15 seconds.
Fully immerse the 3m hose into the water to displace
the air in the hose. Connect the 3m hose to the pow-
er washer and make sure that the inlet strainer re-
mains under water.
With the spray gun removed, switch the power wash-
er on and operate it until water flows uniformly out
of the high-pressure hose. If no water is coming out
of the high-pressure hose after 25 seconds, switch
the power washer off and check all connections. As
soon as water flows out of the high-pressure hose,
switch the power washer off and connect the gu-
nand lance to begin with the work.
It is important that hose and couplings are of good
quality and are tightly connected, and that the seals
are undamaged and properly inserted. Loose con-
nections can impede the priming.
OPERATION
ATTENTION! Dry running of more than 2 minutes
leads to damage of the high-pressure pump.
If the appliance does not build up pressure within
2 minutes, switch the appliance off and proceed in
accordance with the instructions in Chapter "Trou-
bleshooting".
HIGH PRESSURE OPERATION
CAUTION! Keep a distance of at least 30 cm when
using the jet for cleaning painted surfaces to avoid
damage.
CAUTION! Make sure the ON/OFF switch is set
to "OFF/O" and insert the plug into a properly in-
stalled socket.
ATTENTION! The washer must be used on a secure
and stable surface in a standing, upright position.
ATTENTION! Before you start to operate the ma-
chine, make sure that the high pressure hose is fully
unrolled.
Connect the product to power and water supply as
described.
Open the water supply.
ƒ
Hold the trigger gun with both hands.
ƒ
Direct the nozzle away from you towards the sur-
ƒ
face to be cleaned.
Note: Make sure that the release trigger gun button
(15) is on the position unlock so the trigger can be
pressed.
Unlock the trigger and press it until a constant
ƒ
amount of water flows through the nozzle, to al-
low air trapped in the hose to escape (J).
Release the trigger.
ƒ
Turn the switch "ON/OFF" on the position "ON/I"
ƒ
(K).
Hold the trigger gun with both hands. Direct the
ƒ
water jet to the object to be cleaned and press the
trigger.
Release the lever of the trigger gun; the device will
switch off again and stop the water jet. High pres-
sure remains in the system.
WARNING! Beware of kickback when pressing the
trigger!
Note: During longer breaks (more than 5 minutes),
also turn the appliance off using the "ON/OFF"
switch.
OPERATION WITH DETERGENT
Only use cleaning agents suitable specifically for
high pressure washers. We recommend that you use
detergent sparingly for the sake of the environment.
Observe the recommended dilution on the deter-
gent label.
Detergent can only be added when the device is op-
erated in low pressure mode.
HPW 140 EASY
Publicité
