AENO SEASONAL AGH0001S Guide De Démarrage Rapide page 10

 Attach the hole drilling template to the wall, drill holes and screw hooks (See Figures C-4, C-5);
NOTE. Provided hooks and dowels are suitable for reinforced concrete walls only.
 Lean the heater carefully against the wall and hang it on 2 hooks as shown in Figures C-6, C-7;
NOTE. You may also hang the heater on 4 hooks to increase the level of fixation security (See complete
user manual ).
3
 Make sure that the device is securely fixed, and that it is free from dust and dirt. Please adjust the
screwing depth, if necessary.
3. Power on the heater, i.e. plug it into an mains socket with the power cord ❺ . Please do not use an extension
cord to plug it in! Press the power button ❶ . It shall flash green.
4. Activate the device in the mobile app as follows (or scan the QR Code on page 8):
a. Connect your smartphone to Wi-Fi (2.4 GHz) and log in to your AENO app account (or download the
mobile application from Google Play or App Store and register a new user account);
b. Click on the "+" icon in the "Home" tab and select the "Autosearch" tab at the top of the screen;
c. Allow all requested accesses to the AENO app;
d. Wait for the heater to be detected and tap "Next";
e. Enter your Wi-Fi network credentials and tap "Next;
f. Wait till the connection process is completed, and tap "Done".
NOTE. If your device was not detected during this process, press and hold the power button for 4 to 9 seconds,
wait till the LED starts blinking purple, and select "Add manually" tab instead of "Autosearch".
NOTE. You may also activate the device in Google Assistant or Amazon Alexa
5. Set timers or operating scenarios in the mobile application, as may be required, or control the device
manually (See complete user manual
Ceiling Mounting. Option to mount the device on the ceiling is available after its activation in the mobile app,
and shall be performed by qualified installers only. See complete user manual
SAFE OPERATION RULES
ATTENTION! Hot surface! The risk of burns in the case of contact with heated surfaces! Do not touch the
heating panel until completely cooled down!
The power cable must never be in contact with the heat-emitting panel!
Neither cover the heater nor dry things on it. Do not mount the device directly below/above the mains socket.
Do not use the device, if its glass panels are damaged. Protect the device from water and mechanical damage.
Do not install it in areas accessible to children and pets. Do not move or touch the device when it is on or hot.
ATTENTION! It is also strongly recommended to place/mount the heater at a distance of at least 1 meter from
any fabrics, furniture, decorations and any other flammable materials in order to prevent from the risk of
combustion due to high flammability of such materials. Violating these recommendations is done at the risk
of the user, and the manufacturer shall not be liable for any damages caused by such violation.
ATTENTION! If the device is damaged due to tilting or falling, this will void the manufacturer's warranty.
TROUBLESHOOTING
1. The heater does not heat up when turned on: The desired temperature was set incorrectly. Please set the
desired temperature higher than the current one.
2. The heater does not respond to commands from the mobile app: The network connection failure occurred.
Please reconnect the device to the Wi-Fi network.
3. During operation, the heater beeps, and the LED indicator is blinking red: The heater is tilted dangerously.
Please return the heater to the upright position.
Some components, accessories, and/or functions may not be present in your heater configuration. See the box or product page
1
at aeno.com.
The device is intended for indoor installation. Operating conditions: 0°C to +40°C, up to 75% RH (non-condensing). See date of
2
manufacture on the package.
All information contained herein is subject to amendments without prior notification of the User. For current information and
3
details on the device description and specification, connection process, certificates, warranty and quality issues, as well as the
AENO app functionality, see relevant Installation and Operation Manuals available for downloading at aeno.com/documents.
Manufacturer: ASBISc Enterprises PLC, Iapetou, 1, Agios Athanasios, 4101, Limassol, Cyprus. Made in Poland. All trademarks and
names herein are the property of their respective owners.
For some third-party applications, the device must be first activated in the AENO app.
4
10
).
3
, if required.
4
.
3
aeno.com/documents