Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. mr.Kate Manuels
  4. Ameublement d'intérieur
  5. 7769339COM
  6. Mode d'emploi

mr.Kate 7769339COM Mode D'emploi

Lit mural escamotable
Masquer les pouces

Publicité

Liens rapides

Télécharger ce manuel
7769339COM
Full Wall Bed
Date of Purchase ___ / ___ / ___
Lot Number:
WARNING:
* WARNING FOR YOUNG CHILDREN -
This product contains small components,
please ensure that they are kept away
from small children. Children under the
age of 6, small infants and babies must
not sleep on this bed for safety reasons.
To prevent injury and damage to this unit,
PROHIBIT jumping on it.
* This product is designed for home use
and not intended for commercial use.
Do Not Return This Product!
Contact our customer service team for help first.
Call: 1-800-489-3351 (toll free)
Visit: www.ameriwoodhome.com
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Professional installation is
required for this unit.
WARNING
- Unit can tip over causing severe injury or death.
- Anchor unit to stud in wall
- Do Not allow children to climb on unit
Professional
Easy
Assembly Difficulty Meter
Follow Ameriwood Home
You
Tube
B347769339COM0

Publicité

loading

Manuels Connexes pour mr.Kate 7769339COM

Sommaire des Matières pour mr.Kate 7769339COM

  • Page 1 7769339COM Full Wall Bed B347769339COM0 Date of Purchase ___ / ___ / ___ Lot Number: WARNING: * WARNING FOR YOUNG CHILDREN - This product contains small components, please ensure that they are kept away from small children. Children under the age of 6, small infants and babies must not sleep on this bed for safety reasons.
  • Page 2 Contact Us! Do NOT return this product! Contact our friendly customer service team first for help. Call us! 1-800-489-3351 Visit ameriwoodhome.com to view the limited warranty valid in the U.S. and Canada. Helpful Hints - Open your item in the area you plan to keep it to avoid excessive heavy lifting. - Identify, sort and count the parts before attempting assembly.
  • Page 3 Before You Start Read through each step carefully and follow the proper order Separate and count all your parts and hardware Parts are labeled on the surface or edge of the part Give yourself enough room for the assembly process Have the following tools: #2 Phillips Head Screwdriver, Hammer, Level, Stud Finder, Pencil, Step Ladder, Rubber Mallet and a Drill with 1/8"...
  • Page 4 Board Identification Not actual size ameriwoodhome.com...
  • Page 5 Board Identification Parts List ITEM PART NUMBER DESCRIPTION 37769339010 LEFT PANEL 37769339020 RIGHT PANEL 37769339030 37769339040 SUPPORT 37769339050 VALANCE 37769339060 UPPER BACK PANEL 37769339070 CENTER BACK PANEL 37769339080 UPPER SHELF 37769339090 HEADBOARD PANEL 37769339100 STOP RAIL 37769339110 LOWER SHELF 37769339120 SHELF RAIL 37769339130 VERTICAL DOOR MOLDING...
  • Page 6 Note that your unit may contain extra hardware Part List Actual Size (x30) (x30) (x30) (x12) (x12) #A22610 #A22620 #A21660 #A22910 #A22900 cam bolt cam lock wood dowel connector bolt connector (x32) (x8) (x16) (x4) #A14220 #A15520 #A12400 #A13020 #10 x 1/2" pan #14 x 1/2"...
  • Page 7 Part List Not Actual Size shown on page 35 ATTENTION / ATENCION / ATTENTION (x1) (x1) (x1) A99570 #B64481 A81340 dual LED light kit warning label touch sensor disk (x8) (x16) #A53460 #A53470 door bracket door bracket ameriwoodhome.com...
  • Page 8 Bed Frame Identification Not Actual Size Note: Not all parts will be identified. Mattress Holder (2) Right Assembly Left Assembly 3678096-20c 3678096-20d 3678096-20a 3678096-20b Right Pivot Arm Wood Slat (28) Plastic Cap (56) Left Pivot Arm Gas Piston (4) U-Bracket (4) 3678096-20f 3678096-20e 3678096-20g...
  • Page 9 Before you start! VERY IMPORTANT INFORMATION! Caution: Failure to use 2 professionals for this assembly could result in unit damage or personal injury. ameriwoodhome.com...
  • Page 10 STEP 1 (x4) (x2) (x6) Proper orientation of Cam Lock Proper orientation of Cam Lock FLIP ameriwoodhome.com...
  • Page 11 STEP 2 (x4) (x8) Proper orientation of Cam Lock Proper orientation of Cam Lock ameriwoodhome.com...
  • Page 12 STEP 3 (x4) (x4) (x3) Proper orientation of Connector Proper orientation of Cam Lock Proper orientation of Cam Lock ameriwoodhome.com...
  • Page 13 STEP 4 (x4) (x8) Proper orientation of Cam Lock Proper orientation of Cam Lock ameriwoodhome.com...
  • Page 14 STEP 5 (x4) ameriwoodhome.com...
  • Page 15 STEP 6 (x4) (x3) Proper orientation of Connector ameriwoodhome.com...
  • Page 16 STEP 7 (x4) (x3) ameriwoodhome.com...
  • Page 17 STEP 8 (x4) (x3) ameriwoodhome.com...
  • Page 18 STEP 9 (x2) (x4) (x6) (x1) Proper orientation of Connector Proper orientation of Cam Lock Proper orientation of Connector Proper orientation of Cam Lock ameriwoodhome.com...
  • Page 19 STEP 10 (x15) ameriwoodhome.com...
  • Page 20 STEP 11 (x8) The Left Pivot Arm (20e) is located in the 3678096COM Wall Bed Mechanism box ameriwoodhome.com...
  • Page 21 STEP 12 (x15) ameriwoodhome.com...
  • Page 22 STEP 13 (x8) The Right Pivot Arm (20f) is located in the 3678096COM Wall Bed Mechanism box ameriwoodhome.com...
  • Page 23 STEP 14 Turn clockwise to lock in place Assembly orientation is critical! unfinished surface unfinished edge ameriwoodhome.com...
  • Page 24 STEP 15 unfinished surface unfinished edge Turn clockwise to lock in place unfinished edge ameriwoodhome.com...
  • Page 25 STEP 16 Turn clockwise to lock in place Please note: Shelf Rail (L) is symmetrical. ameriwoodhome.com...
  • Page 26 STEP 17 Turn clockwise to lock in place Assembly orientation is critical! unfinished surface unfinished edge ameriwoodhome.com...
  • Page 27 STEP 18 ameriwoodhome.com...
  • Page 28 STEP 19 Dowel is closer to the edge here ameriwoodhome.com...
  • Page 29 STEP 20 Press dowels into place. Gently use rubber mallet if needed. ameriwoodhome.com...
  • Page 30 STEP 21 Dowel is closer to the edge here. ameriwoodhome.com...
  • Page 31 STEP 22 ameriwoodhome.com...
  • Page 32 STEP 23 finished edge ameriwoodhome.com...
  • Page 33 STEP 24 Start at one end and work your way to the other end to line parts up before locking cams. ameriwoodhome.com...
  • Page 34 STEP 25 (x4) (x4) With the help of another person, gently lay the unit onto it's front so the glides will be facing the wall. Tap in bushings (11) with a hammer. Screw in adjustable glides (10) all the way. ameriwoodhome.com...
  • Page 35 STEP 26 The next steps are to assemble your electrical hardware Cord length information: 1. The power supply cord is 72” from transformer to the plug's tip 2. The loop wire for the sensor disk, from the transformer is 48” to the center of the loop 3.
  • Page 36 STEP 27 LED Light Kit Assembly Open the package for the LED Light Kit. Everything will be assembled together. First, unclip the LED Light from the Light Plug as shown... unclip light plug LED light Second, you must disassemble the LED Light. Unscrew the cover off the base and then remove the lens piece.
  • Page 37 STEP 28 (x2) (x1) (x1) Place transformer (19a) on the Headboard Panel (I) in the location shown. Thread the power supply plug (19b) in front of the Support (D) if needed for power source. ameriwoodhome.com...
  • Page 38 STEP 29 (x1) With the help of another person, carefully stand the unit upright. During these steps, allow the other person to securely hold unit from tipping over. Place touch sensor disk (20) in location shown in Lower Shelf (K). ameriwoodhome.com...
  • Page 39 STEP 30 (x2) (x1) (x1) With the help of another person holding unit steady upright, take the Loop Sensor (19c) that is connected to the Transformer (19a) and place underneath Lower Shelf (K) at the hole location of the Touch Sensor Disk (20).
  • Page 40 STEP 31 (x2) (x2) A step ladder will be required for this step. With the help of another person holding the unit steady upright, assemble disassembled LED lights (19d) to the Top (C) with screw (14). Thread the LED lights (19d) wires through the holes provided in Top (C) to allow the wires to be on the top surface of the Top (C).
  • Page 41 STEP 32 (x2) clip back together LED light light plug With the help of another person holding the unit upright steady, feed the LED light wires through the wire saddle (16) in the Top (C) and in the Upper Back Panel (F). Pull wires behind the back of the unit.
  • Page 42 STEP 33 With the help of another person holding the unit steady upright, assemble the LED lights back together. First placing the lens into the base and then screwing the cover back to the base as shown below. base lens cover Adjust any wires necessary as needed.
  • Page 43 The next steps are to assemble your unit to the wall Assembled unit MUST be square on the height, width, and depth to function properly Assembled unit MUST be placed flat against the wall Assembled unit MUST be screwed into 3 DIFFERENT wall studs at the top and bottom for safety Screws provided are for drywall and wood studs.
  • Page 44 STEP 34 With the help of another person, place your unit FLUSH against the wall wire hole wire saddle (16) Be sure the light plug wires (19d) are secure in the wire saddle (16) located on Top (C) through the hole in the Upper Back Panel (F).
  • Page 45 STEP 35 Assembled unit MUST be flush on the height, width, and depth to function properly A step ladder will be required. Do not lean against the top of the unit, it may cause sagging If required, unscrew the Glides counter-clockwise as necessary in all 4 corners until your unit is level in all directions...
  • Page 46 STEP 36 You need to locate at least 3 DIFFERENT studs, in the horizontal direction, but 4 is better. Wall Studs TOP (C) Locate the studs in the wall, using a stud finder. Using a pencil, mark the stud locations on the upper surface of the Upper Back Panel (F) above the Top (C).
  • Page 47 STEP 37 (x8) First, make sure that your unit is still level in all directions. Drill 1/8" (3mm) pilot holes through the Upper Back Panel (F) and Support (D) at the stud locator marks. Fasten the unit to the studs in the wall with the screws (17).
  • Page 48 The next steps are to assemble the metal bed frame and mechanism These parts are located in the #3678096COM Wall Bed Mechanism Carton ameriwoodhome.com...
  • Page 49 STEP 38 (x2) (x4) (x1) press in each hole May need a rubber mallet ameriwoodhome.com...
  • Page 50 STEP 39 (x4) (x8) (x8) (x1) ameriwoodhome.com...
  • Page 51 STEP 40 (x4) (x1) (x2) ameriwoodhome.com...
  • Page 52 STEP 41 (x4) (x4) (x4) long end short end The "long" end of each piston is to be fastened to the frame long end long end The ends of both pistons need to be inserted into the groove of the bed frame when assembled. ameriwoodhome.com...
  • Page 53 STEP 42 (x1) (x2) (x2) The cabinet is not shown to allow a clear view of the bed frame assembly With a person on each side, lift the bed mechanism, line up the holes of the Bed Assembly with the large bushing hole of the Left and Right Pivot arm (20e &...
  • Page 54 STEP 43 (x1) (x4) 1. With a person on each side, carefully lift the bed frame in the closed position. 2. While one person pushes the bed frame into the cabinet, passed the 90 degrees, the other person is to engage the "front" Gas Piston (20h) on each side of the unit, to the front pin of the Left and Right Pivot Arm (20e &...
  • Page 55 STEP 43 continued... Image is showing the bed frame pushed into the cabinet, passed 90 degrees. passed 90 degrees Please note: it is normal to see the bed frame in this state prior to the gas pistons being installed. ameriwoodhome.com...
  • Page 56 STEP 44 ATTENTION / ATENCION / ATTENTION (x1) (x1) (x2) (x2) The cabinet is not shown to allow a clear view of the bed frame assembly Pull the bed frame down, then attach Leg (20c) as shown Apply Warning Label here The bed frame is equipped with a locking mechanism to lock the Leg (20c) in place.
  • Page 57 STEP 45 (x12) (x8) (x4) Proper orientation of bracket ameriwoodhome.com...
  • Page 58 STEP 46 (x8) (x12) (x4) Proper orientation of bracket ameriwoodhome.com...
  • Page 59 STEP 47 With the help of another person, lift the assembled Left Door Panel (P), position the Brackets (21) over the three Support Rails of the Bed Frame, and drop into position. Repeat the procedure for the Right Door Panel Assembly (Q). IMPORTANT: First, unlock and flip the leg into the cabinet.
  • Page 60 STEP 48 (x16) (x8) (x8) (x16) With the help of another person, carefully pull the bed frame open Align the entire assembly so that the edges are lined up with the bed frame and push up against the leg. This will set the top gap. Then fasten the panels to the bed frame with the brackets (22).
  • Page 61 STEP 48 continued... View is looking from the top... showing location of brackets (22). BLACK CIRCLES - USE SCREWS 6 & 7 RED CIRCLES - USE SCREWS 6 & 24 (x16) ameriwoodhome.com...
  • Page 62 STEP 49 (x4) (x56) (x28) A step ladder will be required. Do not lean against the top of the unit, it may cause sagging Fasten Stop Rail (J) to the underside of Top (C) with Screws (9) Press a Plastic Cap (20j) at each end of a Wood Slat (20g).
  • Page 63 STEP 50 (x8) With help of another person, gently close the bed frame then assemble the upper rails (N & O). ameriwoodhome.com...
  • Page 64 Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. This bed is designed to accommodate a Full Size Mattress, up to 10" inches thick. * with a maximum weight of 60 lbs (27.2 kgs) * with a minimum weight of 30 lbs (13.6 kgs) After you have finished assembling your wall bed, please keep the assembly manual by...
  • Page 65 Register your product to receive the following: * New trend details - sneak peek on what's new * Surveys - have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service To register your product, visit ameriwoodhome.com Visit your local retailer's website, rate your purchased product and leave us some feedback! ameriwoodhome.com...
  • Page 66 Español Cubierta Delantera Cama de pared: cama de día de tamaño completo Fecha de compra Número de lote ADVERTENCIA: * ADVERTENCIA PARA NIÑOS PEQUEÑOS: Este producto tiene piezas pequeñas, asegúrese de mantenerlas fuera del alcance de los niños pequeños. Los niños menores de 6 años, lactantes pequeños y bebés no deben dormir en esta cama por cuestiones de seguridad.
  • Page 67 Español Consejos útiles PERSONAS NECESARIAS PARA EL ENSAMBLAJE: 2 - Abra el artículo en la zona donde piensa colocarlo para evitar levantarlo por su peso. - Identifique, clasifique y cuente las piezas antes de intentar ensamblarlo. - Asegúrese de orientar siempre la punta que está en la parte superior del bloqueo de leva hacia el borde exterior.
  • Page 68 Español Lista de piezas Numero de pieza Descripcion Articulo Cantidad Panel izquierdo 37769339010 37769339020 Panel derecho Pieza superior 37769339030 Apoyo 37769339040 37769339050 Cenefa Panel trasero superior 37769339060 37769339070 Panel trasero central Estante superior 37769339080 37769339090 Panel de la cabecera Riel de tope 37769339100 37769339110 Estante inferior...
  • Page 69 Español Página 8: Identificación del marco de cama No es el tamaño real Nota: No se identificarán todas las piezas. 21k - Pasador giratorio 21a - Ensamblaje izquierdo 21l - Pasador de horquilla grande 21b - Ensamblaje derecho 21m - Pasador de horquilla pequeño 21c - Pata 21n - Pasador 21d - Soporte de colchón...
  • Page 70 Español Página 20: Paso 11 El brazo pivotante izquierdo (20e) se encuentra en la caja del mecanismo de la cama mural 3678096COM Página 22: Paso 13 El brazo pivotante derecho (20f) se encuentra en la caja del mecanismo de la cama de pared 3678096COM Página 23: Paso 14 Gire en el sentido de las agujas del reloj para bloquear...
  • Page 71 Español Página 34: Paso 25 Con la ayuda de otra persona, coloque suavemente la unidad sobre su parte frontal de modo que las guías queden orientadas hacia la pared. Golpee los casquillos (11) con un martillo. Atornille las guías ajustables (10) hasta el fondo. Página 35: Paso 26 Los siguientes pasos son ensamblar su hardware eléctrico.
  • Page 72 Español Página 36: Paso 27 Montaje del juego de luces LED Abra el paquete del kit de luces LED. Todo se ensamblará. Primero, desenganche la luz LED del enchufe de la luz como se muestra... desabrochar enchufe de luz Luz LED En segundo lugar, debe desmontar la luz LED.
  • Page 73 Español Página 41: Paso 32 Con la ayuda de otra persona que sostenga la unidad en posición vertical, pase los cables de la luz LED a través del soporte del cable (16) en la parte superior (C) y en el panel trasero superior (F). Jale los cables detrás de la parte trasera de la unidad.
  • Page 74 Español Página 44: Paso 34 Con la ayuda de otra persona, coloque su unidad FLUSH contra la pared. Asegúrese de que los cables del enchufe de la luz (19d) estén seguros en el asiento del cable (16) ubicado en la parte superior (C) a través del orificio en el panel trasero superior (F). sillín de alambre ¡NO lo corte en la cama! En la parte trasera de la unidad hay unas muescas que deben ajustarse alrededor de la placa base...
  • Page 75 Español Página 49: Paso 38 Introduzca presionando en cada orificio Puede necesitar un mazo de goma Página 52: Paso 41 Extremo largo Extremo corto El extremo "largo" de cada pistón debe fijarse al marco. Los extremos de ambos pistones deben insertarse en la ranura del marco de cama cuando estén ensamblados.
  • Page 76 Español Página 56: Paso 44 No se muestra el gabinete para permitir una visión clara del conjunto del marco de cama. Jale el marco de cama hacia abajo y luego fije la pata (20c) como se muestra. Aplique la etiqueta de advertencia aquí. El marco de cama está...
  • Page 77 Español Página 62: Paso 49 Se requerirá una escalera de tijera. No se apoye contra la parte superior de la unidad, ya que puede causar flacidez Fije el riel de tope (J) a la parte inferior de la parte superior (C) con tornillos (9) Presione una tapa de plástico (20j) en cada extremo de un listón de madera (20 g).
  • Page 78 Français Couverture avant Lit mural : Lit de jour pleine grandeur Date d’achat Numéro de lot AVERTISSEMENT : * AVERTISSEMENT POUR LES JEUNES ENFANTS: Ce produit a de petites pièces, assurez-vous de les garder hors de la portée des jeunes enfants. Les enfants de moins de 6 ans, les jeunes nourrissons et les nourrissons ne devraient pas dormir dans ce lit pour des raisons de sécurité.
  • Page 79 Français Conseils utiles PERSONNES NÉCESSAIRES À L’ASSEMBLÉE : 2 - Ouvrez l’article dans la zone où vous prévoyez de le placer pour éviter de le soulever en raison de son poids. - Identifier, classer et compter les pièces avant de tenter de les assembler. - Assurez-vous de toujours pointer la pointe en haut du verrou de la came vers le bord extérieur.
  • Page 80 Français Liste des pieces quantite numero de piece description element Panneau de gauche 37769339010 37769339020 Panneau de droite Haut de page 37769339030 37769339040 le soutien 37769339050 valance panneau superieur du dos 37769339060 panneau arriere central 37769339070 etagere superieure 37769339080 panneau de tete de lit 37769339090 37769339100 rail d'arret...
  • Page 81 Français Page 8 : Identification du cadre de lit Ce n’est pas la taille réelle Remarque : Toutes les pièces ne seront pas identifiées. 21k - Goupille pivotante 21l - Grande goupille de fourche 21a - Assemblée de gauche 21m - Petite goupille de fourche 21b - Assemblée de droite 21n - Épingle 21c - Patte...
  • Page 82 Français Page 20 : Étape 11 Le bras de pivot gauche (20e) est situé dans la boîte de mécanisme de lit mural 3678096COM Page 22 : Étape 13 Le bras pivotant droit (20f) est situé dans la boîte de mécanisme de lit mural 3678096COM Page 23 : Étape 14 Faites pivoter dans le sens des aiguilles d’une montre pour verrouiller L’orientation de l’assemblée est essentielle !
  • Page 83 Français Page 34 : Étape 25 Avec l’aide d’une autre personne, placez doucement l’unité sur son devant afin que les guides soient face au mur. Appuyez doucement sur l’insert fileté (11) avec un marteau. Vissez les guides réglables (10) tout le chemin dans. Page 35 : Étape 26 Les prochaines étapes consistent à...
  • Page 84 Français Page 36 : Étape 27 Assemblage de l’ensemble de lumière LED Ouvrez l’ensemble du kit d’éclairage LED. Tout sera assemblé. Tout d’abord, désengagez la lumière LED de la prise de lumière comme indiqué... unfasten Prise d’éclairage Lumière LED Deuxièmement, vous devez démonter la lumière LED. Dévissez le couvercle de la base, puis retirez la pièce de l’objectif.
  • Page 85 Français Page 41 : Étape 32 Avec l’aide d’une autre personne tenant l’unité à la verticale, enfiler les fils lumineux LED à travers le support de câble (16) en haut (C) et sur le panneau arrière supérieur (F). Tirez les fils derrière l’arrière du lit mural.
  • Page 86 Français Page 44 : Étape 34 Avec l’aide d’une autre personne, placez l’unité FLUSH contre le mur. Assurez-vous que les fils de prise d’éclairage (19d) sont fixés dans la selle de fil (16) située sur le dessus (C) à travers le trou dans le panneau supérieur du dos (F). support de cordon Il y a des encoches fournies à...
  • Page 87 Français Page 49 : Étape 38 Poussez dans chaque trou Vous aurez peut-être besoin d’un maillet en caoutchouc Page 52 : Étape 41 Long End Fin courte L’extrémité "longue" de chaque piston doit être fixée au cadre. Les extrémités des deux pistons doivent être insérées dans la rainure du cadre de lit lors de l’assemblage.
  • Page 88 Français Page 56 : Étape 44 Il n’est pas démontré que l’armoire permet une vue claire de l’ensemble du cadre de lit Tirez le cadre du lit vers le bas, puis fixez la jambe (20c) comme indiqué. Appliquez l’étiquette d’avertissement ici. Le cadre de lit est équipé...
  • Page 89 Français Page 62 : Étape 49 Un escabeau sera nécessaire. Ne vous appuyez pas contre le haut de l’unité car cela peut provoquer un affaissement Fixez le rail d’arrêt (J) au bas du haut (C) avec des vis (9) Appuyez sur un capuchon en plastique (20j) à chaque extrémité d’une latte en bois (20g). Appuyez sur les deux bouchons en plastique (20j), fixés à...